Repara tus cosas

Derecho a reparar

Tienda

MSI GP60 2PE Leopard Wireless Card Replacement

Escrito Por: Zoey Calcagno (y 4 de otros participantes)
  • Comentarios: 0
  • Favoritos: 0
  • Terminaciones: 2

Dificultad

Moderado

Pasos

11

Tiempo Requerido

5 - 10 minutos

Secciones

3

Banderas

1

Featured Student Guide

Guía de Estudiante Destacada

Esta guía fue realizada gracias al duro trabajo de nuestros fantásticos estudiantes y ha sido valorada como excepcionalmente genial por el personal de iFixit.

Introducción

Is your wireless card not working? Here's a guide to replace it. Make sure you follow each step accordingly and carefully replace the wireless card.

Herramientas

Comprar estas herramientas

Partes

No se especificaron partes.

  1. Flip MSI GP60 2PE Leopard, so that the back is facing up.

    • Flip MSI GP60 2PE Leopard, so that the back is facing up.

    Traducir

  2. Find the unlock tab located on the upper right side of the device, then slide it to the right.

    • Find the unlock tab located on the upper right side of the device, then slide it to the right.

    Traducir

  3. Slide and hold the release tab on the left side of the battery, so that you can remove the battery. Slide and hold the release tab on the left side of the battery, so that you can remove the battery. Slide and hold the release tab on the left side of the battery, so that you can remove the battery.

    • Slide and hold the release tab on the left side of the battery, so that you can remove the battery.

    Traducir

  4. While holding the release tab, remove the battery slowly. While holding the release tab, remove the battery slowly. While holding the release tab, remove the battery slowly.

    • While holding the release tab, remove the battery slowly.

    Traducir

  6. Flip the device over so the back is facing up.

    • Flip the device over so the back is facing up.

    Traducir

  7. Remove the four 5mm screws from the back of the device using a Phillips #00 screwdriver. There is a screw located under the battery; lift the battery up to access it.

    • Remove the four 5mm screws from the back of the device using a Phillips #00 screwdriver.

    • There is a screw located under the battery; lift the battery up to access it.

    Traducir

  8. Once all four screws are removed, lift the back off. Once all four screws are removed, lift the back off.

    • Once all four screws are removed, lift the back off.

    Traducir

  9. Locate the wireless card.

    • Locate the wireless card.

    Traducir

  10. Using a Phillips #00 screwdriver, remove the one 2 mm screw that is holding the wireless card in place.

    • Using a Phillips #00 screwdriver, remove the one 2 mm screw that is holding the wireless card in place.

    Traducir

  11. Carefully remove the wireless card.

    • Carefully remove the wireless card.

    • Pay close attention to the two wires attached to wireless card.

    Traducir

  12. Remove the wires connecting to the wireless card by pinching around the base where they connect, then carefully disconnect them. The wires should come off fairly easily.

    • Remove the wires connecting to the wireless card by pinching around the base where they connect, then carefully disconnect them.

    • The wires should come off fairly easily.

    • Avoid yanking or pulling too hard. This can result in the wires breaking.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

0 comentarios

Agregar un comentario

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 4

Ultimos 30 días: 24

Todo El Tiempo: 648