Saltar al contenido principal

Partes

No se especificaron partes.

  1. Este paso está sin traducir. Ayuda a traducirlo

    Make sure the laptop is off and unplugged (not charging). With the laptop closed and upside down, unscrew the nineteen 5.5mm Phillips #1 screws that keep the back cover in place.
    • Make sure the laptop is off and unplugged (not charging).

    • With the laptop closed and upside down, unscrew the nineteen 5.5mm Phillips #1 screws that keep the back cover in place.

  2. Este paso está sin traducir. Ayuda a traducirlo

    Slide the optical drive out of the laptop.
    • Slide the optical drive out of the laptop.

  3. Este paso está sin traducir. Ayuda a traducirlo

    Use a Phillips screwdriver to remove the three screws along the edge of the optical drive bay.
    • Use a Phillips screwdriver to remove the three screws along the edge of the optical drive bay.

  4. Este paso está sin traducir. Ayuda a traducirlo

    Using your fingers, gently loosen the edges of all four sides of the back cover. Gently pull off the back cover.
    • Using your fingers, gently loosen the edges of all four sides of the back cover.

    • Gently pull off the back cover.

  5. Este paso está sin traducir. Ayuda a traducirlo

    Unscrew the single 5.5mm Phillips #1 screw keeping the battery secure. Unscrew the single 5.5mm Phillips #1 screw keeping the battery secure.
    • Unscrew the single 5.5mm Phillips #1 screw keeping the battery secure.

  6. Este paso está sin traducir. Ayuda a traducirlo

    Grab the battery with your fingers and gently pull it up and away from the rest of the laptop. Grab the battery with your fingers and gently pull it up and away from the rest of the laptop.
    • Grab the battery with your fingers and gently pull it up and away from the rest of the laptop.

  7. Este paso está sin traducir. Ayuda a traducirlo

    Remove the two 5.5mm screws with the Phillips #1 screwdriver. Remove the two 5.5mm screws with the Phillips #1 screwdriver.
    • Remove the two 5.5mm screws with the Phillips #1 screwdriver.

  8. Este paso está sin traducir. Ayuda a traducirlo

    Gently pull out the hard drive by wiggling it from right to left with your hands until it is removed. Gently pull out the hard drive by wiggling it from right to left with your hands until it is removed.
    • Gently pull out the hard drive by wiggling it from right to left with your hands until it is removed.

Linea de Meta

6 personas más completaron esta guía.

Tanmay Kumar

Miembro Desde 17/04/17

458 Reputación

4 Guías creadas

Equipo

Cal Poly, Team S14-G4, Banghart Spring 2017 Miembro de Cal Poly, Team S14-G4, Banghart Spring 2017

CPSU-BANGHART-S17S14G4

4 Miembros

8 Guías creadas

Un Comentario

I have just bought an MSI GP72VR Laptop and I screwed up and got the model with only one drive, an SSD. It nagged at me that I didn't get the one with 2 drives. Well I happen to build my own desktops and had a spare 500GB Mushkin SSD hanging around and decided, what the heck. I came here and couldn't find the exact model but this is identical for what I want. I have never seen an access like this where you have to remove 19 screws. So I am very happy that this is on iFixit. I removed the screws and couldn't get the bottom removed as shown, I had to go to the other side and then it came off fairly easily. I used a butter knife for the initial pry and that worked well. They had sent the disk holder with the computer so I had no problem installing and I just set it up in Disk Manager. Tanmay, thank you very much for the assist, it is appreciated.

adard745 - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 12

Ultimos 30 días: 63

Todo El Tiempo: 6,315