Saltar al contenido principal

Logitech Dual Action Triggers Repair

Qué necesitas

  1. Logitech Dual Action Triggers Repair, Logitech Dual Action Triggers Repair: paso 1, imagen 1 de 1
    • To get into the controller, you will need to unscrew the 7 screws on the back.

    • You will have to remove the bottom oval sticker to reveal the screw circled in red.

  2. Logitech Dual Action Triggers Repair: paso 2, imagen 1 de 2 Logitech Dual Action Triggers Repair: paso 2, imagen 2 de 2
    • With the screws removed, turn the controller upside down and separate the front end from the back end.

    • It is likely that the buttons will fall out of place, so as you open the controller, try to keep track of where the pieces go.

  3. Logitech Dual Action Triggers Repair: paso 3, imagen 1 de 1
    • There should be 4 circular buttons labeled 1-4, 4 smaller circular buttons for the D-Pad, and 3 oval shaped buttons.

  4. Logitech Dual Action Triggers Repair: paso 4, imagen 1 de 3 Logitech Dual Action Triggers Repair: paso 4, imagen 2 de 3 Logitech Dual Action Triggers Repair: paso 4, imagen 3 de 3
    • In the center of the controller, pull upwards on the USB cord.

    • Be careful not to pull hard enough to yank the wires connecting to the logic board.

    • With the wire out of the way, remove the screw it exposed. This will disconnect the logic board from the controller.

  5. Logitech Dual Action Triggers Repair: paso 5, imagen 1 de 3 Logitech Dual Action Triggers Repair: paso 5, imagen 2 de 3 Logitech Dual Action Triggers Repair: paso 5, imagen 3 de 3
    • To remove the triggers, push upwards from the back on them.

    • Once far enough, detach the logic board from the back cover piece and the triggers.

  6. Logitech Dual Action Triggers Repair: paso 6, imagen 1 de 2 Logitech Dual Action Triggers Repair: paso 6, imagen 2 de 2
    • If the wire is unplugged solely from the logic board, you can fasten it back into its place.

    • Look at the second picture to see where the wires go.

  7. Logitech Dual Action Triggers Repair: paso 7, imagen 1 de 3 Logitech Dual Action Triggers Repair: paso 7, imagen 2 de 3 Logitech Dual Action Triggers Repair: paso 7, imagen 3 de 3
    • Unscrew the screw on the trigger to remove the back cover.

    • Once removed, carefully pull the back cover off.

  8. Logitech Dual Action Triggers Repair: paso 8, imagen 1 de 1
    • The 3 wires are soldered into the 3 spots circled on the picture.

    • You can now fasten the wire into the right spot on the trigger piece.

Conclusión

To reassemble your device, follow these instructions in reverse order.

4 personas más completaron esta guía.

Brian Neuman

Miembro Desde 01/20/15

893 Reputación

3 Guías creadas

Equipo

USF Tampa, Team 7-4, Remmell Winter 2015 Miembro de USF Tampa, Team 7-4, Remmell Winter 2015

USFT-REMMELL-W15S7G4

4 Miembros

3 Guías creadas

2 comentarios

Hi dear, can you say me the order of colours in the USB cable? I think green, white, red, black thin and black thick. Is It correct?

Cas - Contestar

Where can I get conductive pads for this?

Ginga - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 3

Ultimos 7 días: 14

Ultimos 30 días: 66

Todo El Tiempo: 8,829