Repara tus cosas Comunidad Tienda

Lite-On LightScribe SHM-165H6S Drive Belt Replacement

Introducción

If your drive is having problems opening, the drive belt may have broken or fallen out of the track and you will need to replace it.

Qué necesitas

  1. Lite-On LightScribe SHM-165H6S Drive Belt Replacement, Chassis: paso 1, imagen 1 de 2 Lite-On LightScribe SHM-165H6S Drive Belt Replacement, Chassis: paso 1, imagen 2 de 2

    • Insert an open paper clip into the small hole on the left side of the faceplate.

    • After the tray opens, extend it fully.

    Editar

  2. Lite-On LightScribe SHM-165H6S Drive Belt Replacement: paso 2, imagen 1 de 3 Lite-On LightScribe SHM-165H6S Drive Belt Replacement: paso 2, imagen 2 de 3 Lite-On LightScribe SHM-165H6S Drive Belt Replacement: paso 2, imagen 3 de 3

    • Use an opening device to push in the black tabs on the left, right and bottom of the outer chassis to unhook the faceplate.

    Editar

  3. Lite-On LightScribe SHM-165H6S Drive Belt Replacement: paso 3, imagen 1 de 1

    • Pull the faceplate away from the main chassis.

    Editar

  5. Lite-On LightScribe SHM-165H6S Drive Belt Replacement: paso 4, imagen 1 de 1

    • Unscrew the four 8.5 mm screws on the bottom chassis using a Philips #2 screwdriver.

    Editar

  6. Lite-On LightScribe SHM-165H6S Drive Belt Replacement: paso 5, imagen 1 de 2 Lite-On LightScribe SHM-165H6S Drive Belt Replacement: paso 5, imagen 2 de 2

    • Lift the top and bottom chassis straight up in order to remove them.

    Editar

  7. Lite-On LightScribe SHM-165H6S Drive Belt Replacement, Drive Belt: paso 6, imagen 1 de 2 Lite-On LightScribe SHM-165H6S Drive Belt Replacement, Drive Belt: paso 6, imagen 2 de 2

    • Extend the tray so that the belt is accessible.

    • Remove the old belt using tweezers.

    Editar

  8. Lite-On LightScribe SHM-165H6S Drive Belt Replacement: paso 7, imagen 1 de 2 Lite-On LightScribe SHM-165H6S Drive Belt Replacement: paso 7, imagen 2 de 2

    • Carefully replace with the new belt by wrapping it around the larger gear first, followed by the smaller gear.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

5 personas más completaron esta guía.

Autor

con 7 otros colaboradores

James Biggs

Miembro Desde 10/12/11

596 Reputación

3 Guías creadas

Insignias: 17

+ 14 más insignias

Equipo

Cal Poly, Team 6-5, Regan Fall 2011 Miembro de Cal Poly, Team 6-5, Regan Fall 2011

CPSU-REGAN-F11S6G5

2 Miembros

6 Guías creadas

Un comentario

In case anyone is interested, I used a 11/16” OD x 9/16” I.D. x 1/16” wall, for this exact drive (was a tight fit) and seems to work perfect.

I was so tired of replacing rubber bands every few months!

And yes this is an “O-ring”  it should be less than a buck five eighty at your local big box hardware store.

Jim Mccalb - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 1

Ultimos 30 días: 12

Todo El Tiempo: 6,522