Repara tus cosas

Derecho a reparar

Tienda

Left Joy-Con Buttons Replacement

Escrito Por: Joshua Thomas (y 5 de otros participantes)
  • Comentarios: 9
  • Favoritos: 1
  • Terminaciones: 12

Dificultad

Moderado

Pasos

15

Tiempo Requerido

30 minutos - 1 hora

Secciones

1

Banderas

0

Introducción

This guide was created to assist users in replacing the buttons on their left Nintendo Switch Joy-con. Please note that this guide does not contain steps for the right Joy-Con. The process for the right Joy-con is different and a bit more difficult. The process for replacing the buttons in the left Joy-Con consists of opening the Joy-Con, removing each of the inner pieces, batteries, and motherboard, then locating, removing, and replacing the desired buttons.

  1. Remove the four screws located on the back casing with a Y00 screwdriver. Insert a plastic opening tool or pick into the side of the Joy-Con without the rail and gently pry downwards to release the back plate.

    • Remove the four screws located on the back casing with a Y00 screwdriver.

    • Insert a plastic opening tool or pick into the side of the Joy-Con without the rail and gently pry downwards to release the back plate.

    Editar

  2. Open the Joy-Con toward the rail side, like a book.

    • Open the Joy-Con toward the rail side, like a book.

    • Be careful not to damage the two fragile ribbon cables attaching the rails to the motherboard.

    Editar

  3. Insert a spudger or plastic opening tool underneath the battery and gently begin prying downward to release the adhesive holding the battery in place.

    • Insert a spudger or plastic opening tool underneath the battery and gently begin prying downward to release the adhesive holding the battery in place.

    • Remove the battery from the inner casing.

    • Be careful not to pull too hard on the battery, as it is connected to the motherboard by a cord and you could risk damaging it.

    Editar

  4. Gently pull the cord that's connecting the battery to the motherboard up and out of the Joy-Con.

    • Gently pull the cord that's connecting the battery to the motherboard up and out of the Joy-Con.

    Editar

  5. Take a Phillips #2 screwdriver and remove the two screws adjacent to each other that are locking the inner casing into place. Take a Phillips #2 screwdriver and remove the two screws adjacent to each other that are locking the inner casing into place.

    • Take a Phillips #2 screwdriver and remove the two screws adjacent to each other that are locking the inner casing into place.

    Editar

    There is also a phillips screw in the bottom right of the picture that needs to be removed before removing the battery holder.

    Ben Masten - Contestar

  7. Open up the inner casing in the opposite direction you opened up the outer casing.

    • Open up the inner casing in the opposite direction you opened up the outer casing.

    • Be careful not to damage the one fragile ribbon cable attaching the inner casing to the motherboard.

    Editar

    It should be noted the parts of the inner casing that are closest to the rail have adhesive on them that may need a little coaxing (seen in white on the right side of the above image)

    Sami Ring - Contestar

  8. Using tweezers, gently lift up on the black or grey clasps holding down each of the 5 ribbon cables connected to the motherboard.

    • Using tweezers, gently lift up on the black or grey clasps holding down each of the 5 ribbon cables connected to the motherboard.

    • Using the tweezers, gently pull each of the ribbon cables out from their connections.

    Editar

  9. Using a Phillips #2 screwdriver, unscrew both screws connecting the analog stick to the motherboard.

    • Using a Phillips #2 screwdriver, unscrew both screws connecting the analog stick to the motherboard.

    Editar

    Don’t forget to take off the blue ribon at the right side of the right screw

    max_maxi - Contestar

  10. Carefully lift the analog stick up and out from the Joy-Con.

    • Carefully lift the analog stick up and out from the Joy-Con.

    Editar

  11. Using a Phillips #2 screwdriver, remove the two screws holding the motherboard in place.

    • Using a Phillips #2 screwdriver, remove the two screws holding the motherboard in place.

    Editar

  12. Carefully remove the rumble pack connected to the motherboard by gently lifting it out of its casing. You may need to lift with a little force, as this piece is connected with adhesive.

    • Carefully remove the rumble pack connected to the motherboard by gently lifting it out of its casing.

    • You may need to lift with a little force, as this piece is connected with adhesive.

    • Do not disconnect the cord connecting the rumble pack to the motherboard.

    • Carefully lift both the rumble pack and motherboard out of the outer casing.

    Editar

  13. Using a Phillips #2 screwdriver, remove the three screws holding the minus button and L button into place.

    • Using a Phillips #2 screwdriver, remove the three screws holding the minus button and L button into place.

    Editar

  14. Locate and remove all of the rubber casings covering the buttons.

    • Locate and remove all of the rubber casings covering the buttons.

    Editar

  15. Use tweezers to remove all the buttons that you would like to replace.

    • Use tweezers to remove all the buttons that you would like to replace.

    • Be careful not to turn the Joy-Con over as the buttons are now loose and could fall out.

    Editar

  16. Using tweezers, carefully place all your new buttons into the Joy-Con.

    • Using tweezers, carefully place all your new buttons into the Joy-Con.

    • Make sure each of the notches on the buttons are properly lined up to the notches in the Joy-Con. Failure to do so could lead to non-responsive buttons.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order. Make sure when you are screwing the motherboard back into place you do not screw it in too tightly. If the motherboard is too tight to the buttons it could keep the buttons from pushing properly.

12 personas más completaron esta guía.

6 comentarios

Agregar un comentario

My left directional button is nonresponsive. Can I fix this by dropping in a replacement left directional button? Would the rubber cover need to be replaced as well?

Blade Dub - Contestar

just incase you havent done so already, it might not be the button. it might be the motherboard, connectors, and a whole slew of other problems.

john gerardo -

What type of switch is the minus button? It’s on the same ribbon as the L micro switch. My L switch is bad and I’m replacing it I just would like to know the name of the type of switch used on the minus button.

brantleycmd - Contestar

Thank you for the helpful guide! Is there a guide for the right Joy Con available anywhere?

ericsajedi - Contestar

Eric, no one has made a guide for the right Joy-Con yet! I’ve taken them both apart and the buttons are pretty similar. I think you can use Joshua’s button guide here and this joystick guide to guide you to the buttons in the other Joy-Con! If you do end up attempting it, consider taking some photos and making a guide for future right Joy-Con fixers. :)

Taylor Dixon -

Thanks for sharing this awesome guide! The first Joy-Con repair went great but i just tried repairing a second Joy-Con and after calibrating it’s drifting really bad. The replacement joystick I used was from Amazon and only $6 so I’m assuming that’s why it didn’t work. I just ordered a new replacement joystick from iFixit so hopefully that one is better quality and works. Thanks again!

ericsajedi - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 24

Ultimos 7 días: 213

Ultimos 30 días: 961

Todo El Tiempo: 19,847