Introducción

Steps to remove LG VX8550 slider mechanism

Slide the battery release up.
  • Slide the battery release up.

Agregar Comentario

Remove the battery by lifting away from the case.
  • Remove the battery by lifting away from the case.

Agregar Comentario

Remove the 2 screw covers next to the rear speaker with a Push Pin.
  • Remove the 2 screw covers next to the rear speaker with a Push Pin.

Agregar Comentario

Remove the 4 cover screws with a Philips #00 screwdriver.
  • Remove the 4 cover screws with a Philips #00 screwdriver.

Agregar Comentario

Use the iPod opening tool to pry off the back casing.
  • Use the iPod opening tool to pry off the back casing.

Agregar Comentario

Continue sliding the iPod opening tool around the seam of the casing to separate the front and back casings.
  • Continue sliding the iPod opening tool around the seam of the casing to separate the front and back casings.

Agregar Comentario

Separate the casing halves.
  • Separate the casing halves.

  • Be sure to keep track of the side buttons as they fall out.

Agregar Comentario

Remove the 2 screws from the back of the phone with a Phillips #00 Screwdriver.
  • Remove the 2 screws from the back of the phone with a Phillips #00 Screwdriver.

Agregar Comentario

Carefully lift up on the motherboard to see the ribbon cables underneath.
  • Carefully lift up on the motherboard to see the ribbon cables underneath.

  • Use the spudger to carefully disconnect the ribbon cable from the motherboard.

Agregar Comentario

Remove the motherboard from the front casing by lifting straight up.
  • Remove the motherboard from the front casing by lifting straight up.

Agregar Comentario

Lay the phone with the screen facedown.
  • Lay the phone with the screen facedown.

  • The 6 slider screws are visible.

Agregar Comentario

Peel back but don't remove the blue tape to access the 2 center screws.
  • Peel back but don't remove the blue tape to access the 2 center screws.

  • Remove the 6 slider screws with the Phillips #00 screwdriver.

Agregar Comentario

Lift the keypad housing away from the slider.
  • Lift the keypad housing away from the slider.

Agregar Comentario

Remove the 2 screw covers next to the speaker with a push pin next to the camera.
  • Remove the 2 screw covers next to the speaker with a push pin next to the camera.

Agregar Comentario

Remove the 6 screws with a Phillips #00 Screwdriver.
  • Remove the 6 screws with a Phillips #00 Screwdriver.

Agregar Comentario

Use the ipod opening tool to pry the screen casing and the slider mechanism apart from each other.
  • Use the ipod opening tool to pry the screen casing and the slider mechanism apart from each other.

Agregar Comentario

Carefully lift the slider mechanism to see the ribbon cables underneath.
  • Carefully lift the slider mechanism to see the ribbon cables underneath.

Agregar Comentario

Slide ribbon cable through the slider mechanism.
  • Slide ribbon cable through the slider mechanism.

Agregar Comentario

Separate the two halves.
  • Separate the two halves.

Agregar Comentario

With the slider mechanism separated from the screen casing the 8 screws securing the slider mechanism are visible.
  • With the slider mechanism separated from the screen casing the 8 screws securing the slider mechanism are visible.

  • Remove the 8 screws.

Agregar Comentario

Remove slider mechanism.  Now is a good time to clean slider mechanism if sticky.
  • Remove slider mechanism. Now is a good time to clean slider mechanism if sticky.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Nathan Jones

Miembro Desde 10/04/10

83 Reputación

20 Guías creadas

Equipo

Cal Poly, Team 34-55, Forte Spring 2010 Miembro de Cal Poly, Team 34-55, Forte Spring 2010

CPSU-FORTE-S10S34G55

5 Miembros

20 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 0

Todo El Tiempo: 2,993