Saltar al contenido principal

Partes

No se especificaron partes.

  1. Este paso está sin traducir. Ayuda a traducirlo

    Begin by taking the back battery cover off. Put your index finger on the white notch and apply pressure.
    • Begin by taking the back battery cover off.

    • Put your index finger on the white notch and apply pressure.

    • While applying pressure, move your hand backwards to slide the battery cover off of the body of the phone.

  2. Este paso está sin traducir. Ayuda a traducirlo

    Remove the battery. Put your index finger in the notch above the battery near the top of the casing.
    • Remove the battery.

    • Put your index finger in the notch above the battery near the top of the casing.

    • While applying pressure against the battery, lift up and take out the battery.

  3. Este paso está sin traducir. Ayuda a traducirlo

    Remove the SIM card from its housing. Put your finger in the provided notch below the SIM card and begin to push the SIM card towards the top of the device. After it is out of the metal housing, it is free to be removed.
    • Remove the SIM card from its housing.

    • Put your finger in the provided notch below the SIM card and begin to push the SIM card towards the top of the device.

    • After it is out of the metal housing, it is free to be removed.

  4. Kits de Reparación de Android

    A new screen or battery is one kit away.

    Comprar Ahora

    Kits de Reparación de Android

    A new screen or battery is one kit away.

    Comprar Ahora
  5. Este paso está sin traducir. Ayuda a traducirlo

    Remove the four screws along the edge of the phone body, as shown in the picture to the left.
    • Remove the four screws along the edge of the phone body, as shown in the picture to the left.

  6. Este paso está sin traducir. Ayuda a traducirlo

    Using the plastic opening tool, pry open the body of the phone, starting at the bottom of the phone (this tends to be the easiest place to start). Double check to make sure the SIM card is removed from its housing. You will not be able to pry open the body of the phone if the SIM card remains in its housing.
    • Using the plastic opening tool, pry open the body of the phone, starting at the bottom of the phone (this tends to be the easiest place to start).

    • Double check to make sure the SIM card is removed from its housing. You will not be able to pry open the body of the phone if the SIM card remains in its housing.

    • Continue by sliding the opening tool around the perimeter of the phone. You should hear multiple clicking sounds as you complete this, indicating the clips are becoming unlatched.

    • This may take a few tries to get correct. Don't give up if it doesn't work the very first time.

  7. Este paso está sin traducir. Ayuda a traducirlo

    Put the red casing aside and remove the motherboard from the front casing of the phone by carefully dislodging it from its two clips near the top of the phone. Put the red casing aside and remove the motherboard from the front casing of the phone by carefully dislodging it from its two clips near the top of the phone. Put the red casing aside and remove the motherboard from the front casing of the phone by carefully dislodging it from its two clips near the top of the phone.
    • Put the red casing aside and remove the motherboard from the front casing of the phone by carefully dislodging it from its two clips near the top of the phone.

  8. Este paso está sin traducir. Ayuda a traducirlo

    The upper left corner of the LCD display will be held in place with a small clip. Gently pull the small clip outwards, away from the surface of the motherboard. As shown in the second photo, the lower right hand corner will still be attached to the motherboard. DO NOT try to remove this part yet.
    • The upper left corner of the LCD display will be held in place with a small clip. Gently pull the small clip outwards, away from the surface of the motherboard.

    • As shown in the second photo, the lower right hand corner will still be attached to the motherboard. DO NOT try to remove this part yet.

  9. Este paso está sin traducir. Ayuda a traducirlo

    The LCD screen is attached by a small ribbon to the motherboard. Gently pull the screen out of the clip it is attached to. Notice: When re-installing a new LCD screen, make sure to prop up the black clip before installing the ribbon cord, as shown in the pictures. Notice: When re-installing a new LCD screen, make sure to prop up the black clip before installing the ribbon cord, as shown in the pictures.
    • The LCD screen is attached by a small ribbon to the motherboard. Gently pull the screen out of the clip it is attached to.

    • Notice: When re-installing a new LCD screen, make sure to prop up the black clip before installing the ribbon cord, as shown in the pictures.

Linea de Meta

2 personas más completaron esta guía.

Preston Brown

Miembro Desde 12/04/12

22 Reputación

5 Guías creadas

Equipo

Cal Poly, Team 6-20, Amido Spring 2012 Miembro de Cal Poly, Team 6-20, Amido Spring 2012

CPSU-AMIDO-S12S6G20

4 Miembros

10 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 1

Últimos 30 Días: 6

Todo El Tiempo: 1,342