Repara tus cosas Comunidad Tienda

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

Kodak Easyshare C813 Logic Board Replacement

Introducción

This guide demonstrates how to replace the camera's logic board.

Qué necesitas

  1. Kodak Easyshare C813 Logic Board Replacement, Battery: paso 1, imagen 1 de 1

    • Turn off camera by firmly pressing the power button that is located on the top of the camera near the selector dial.

    Traducir

  2. Kodak Easyshare C813 Logic Board Replacement: paso 2, imagen 1 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 2, imagen 2 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 2, imagen 3 de 3

    • Press thumb firmly on battery door and slide it in the direction of the arrow.

    • Lift thumb allowing the door to swing open.

    Traducir

  3. Kodak Easyshare C813 Logic Board Replacement, Back Cover: paso 3, imagen 1 de 1
    Herramienta utilizada en este paso:
    Anti-Static Wrist Strap
    $7.95
    Comprar
    Traducir

  4. Kodak Easyshare C813 Logic Board Replacement: paso 4, imagen 1 de 1

    • Turn the camera off by firmly pressing the power button located on top of the camera.

    Traducir

  5. Kodak Easyshare C813 Logic Board Replacement: paso 5, imagen 1 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 5, imagen 2 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 5, imagen 3 de 3

    • Locate the 7 screws holding the back cover on.

    • Three screws are located on the bottom of the camera.

    • Two screws are located on the side shown in the photograph.

    • Two final screws are located on the opposite side shown in the photograph.

    Traducir

  6. Kodak Easyshare C813 Logic Board Replacement: paso 6, imagen 1 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 6, imagen 2 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 6, imagen 3 de 3
    Herramienta utilizada en este paso:
    Phillips #00 Screwdriver
    $5.49
    Comprar

    • Remove all 7 screws:

    • Hold the camera firmly with one hand so that you can still see a screw.

    • Place the Philips 00(Found here)screwdriver into the screw.

    • Turn the screwdriver to the left until it is free.

    • Repeat for the remaining screws.

    Traducir

  7. Kodak Easyshare C813 Logic Board Replacement: paso 7, imagen 1 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 7, imagen 2 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 7, imagen 3 de 3

    • Use plastic opening tools to slightly open the side of the case.

    • Insert a plastic opening tool and apply pressure to the internal three tabs at the top.

    • The first two are near the words "3X Optical Zoom".

    • The third is near the shutter button.

    Traducir

  8. Kodak Easyshare C813 Logic Board Replacement: paso 8, imagen 1 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 8, imagen 2 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 8, imagen 3 de 3

    • Gently pull apart the back cover from the rest of the camera.

    • Make sure there are no more screws or tabs keeping the cover on.

    • Use the plastic opening tool to separate any sides still closely connected.

    Traducir

  10. Kodak Easyshare C813 Logic Board Replacement, Front Cover: paso 9, imagen 1 de 2 Kodak Easyshare C813 Logic Board Replacement, Front Cover: paso 9, imagen 2 de 2

    • Open the battery door.

    • Press thumb firmly on battery door and slide it in the direction of the arrow.

    • Lift thumb allowing the door to swing open.

    Traducir

  11. Kodak Easyshare C813 Logic Board Replacement: paso 10, imagen 1 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 10, imagen 2 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 10, imagen 3 de 3

    • Use the plastic opening tool to lift the casing around the shutter button.

    • Gently remove the front cover from the device.

    Traducir

  12. Kodak Easyshare C813 Logic Board Replacement: paso 11, imagen 1 de 1

    • Do not touch the terminals shown in the photo. These link to the capacitor which could shock you if not discharged.

    • To discharge the capacitor follow this guide.

    Traducir

  13. Kodak Easyshare C813 Logic Board Replacement, LCD: paso 12, imagen 1 de 3 Kodak Easyshare C813 Logic Board Replacement, LCD: paso 12, imagen 2 de 3 Kodak Easyshare C813 Logic Board Replacement, LCD: paso 12, imagen 3 de 3

    • Once the front cover is removed, the battery door maybe closed for convenience.

    • Locate the exposed portion of the LCD screen.

    • Use a wedge to free the LCD screen from the medal housing.

    • Do not pull the screen away completely, it is still attached to the logic board via the yellow cable.

    Traducir

  14. Kodak Easyshare C813 Logic Board Replacement: paso 13, imagen 1 de 1

    • Remove the screw at the upper right corner of the metal housing.

    Traducir

  15. Kodak Easyshare C813 Logic Board Replacement: paso 14, imagen 1 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 14, imagen 2 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 14, imagen 3 de 3

    • Locate the 2 solder joints holding down the medal housing.

    • Remove the solder.

    • Place wick on solder.

    • Place solder iron on wick

    • The wick should be sandwiched between the iron and the solder.

    Traducir

  16. Kodak Easyshare C813 Logic Board Replacement: paso 15, imagen 1 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 15, imagen 2 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 15, imagen 3 de 3

    • Peel back the black tape from the metal housing.

    • Lift the metal housing from the left so that it hinges on its right side.

    • The metal housing is still loosely attached on its right side.

    Traducir

  17. Kodak Easyshare C813 Logic Board Replacement: paso 16, imagen 1 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 16, imagen 2 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 16, imagen 3 de 3

    • Locate black tab holding the LCD screen connector in the port.

    • Use wedge or fingernail to lift the black tab.

    • Pull the the LCD screen connector out of the port.

    Traducir

  18. Kodak Easyshare C813 Logic Board Replacement, Logic Board: paso 17, imagen 1 de 1

    • Remove the medal housing from the logic board by carefully peeling the yellow tape off of the metal housing.

    Traducir

  19. Kodak Easyshare C813 Logic Board Replacement: paso 18, imagen 1 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 18, imagen 2 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 18, imagen 3 de 3

    • Locate the 2 screws on the yellow tape.

    • Remove the 2 screws.

    • Remove the yellow tape.

    Traducir

  20. Kodak Easyshare C813 Logic Board Replacement: paso 19, imagen 1 de 2 Kodak Easyshare C813 Logic Board Replacement: paso 19, imagen 2 de 2

    • Locate the 2 solder joints near the shutter button.

    • Remove the solder on both joints with the wick and soldering iron in the same manner as Step 11.

    Traducir

  21. Kodak Easyshare C813 Logic Board Replacement: paso 20, imagen 1 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 20, imagen 2 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 20, imagen 3 de 3

    • Turn the camera over.

    • Remove the screw holding the small green board.

    • Lift the small green board.

    • The small green board is still attached to the logic board via wires.

    Traducir

  22. Kodak Easyshare C813 Logic Board Replacement: paso 21, imagen 1 de 1

    • Desolder the remaining 20 solder joints connecting the logic board to the camera.

    Traducir

  23. Kodak Easyshare C813 Logic Board Replacement: paso 22, imagen 1 de 2 Kodak Easyshare C813 Logic Board Replacement: paso 22, imagen 2 de 2

    • Locate the black tab holding the yellow cable in place.

    • Use a plastic opening tool or fingernail to lift the black tab.

    • Pull the yellow cable from the port.

    Traducir

  24. Kodak Easyshare C813 Logic Board Replacement: paso 23, imagen 1 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 23, imagen 2 de 3 Kodak Easyshare C813 Logic Board Replacement: paso 23, imagen 3 de 3

    • Use a plastic opening tool to lift the board from the camera.

    • Continue to remove the board completely.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 7 otros colaboradores

Susan Marano

Miembro Desde 04/15/10

336 Reputación

7 Guías creadas

Insignias: 16

+ 13 más insignias

Equipo

Cal Poly, Team 24-22, Regan Spring 2010 Miembro de Cal Poly, Team 24-22, Regan Spring 2010

CPSU-REGAN-S10S24G22

4 Miembros

20 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 7

Ultimos 30 días: 11

Todo El Tiempo: 4,172