Repara tus cosas

Derecho a reparar

Tienda

KitchenAid KHM512ER Power Cord Replacement

Escrito Por: Brad Daniels (y 3 de otros participantes)
  • Comentarios: 0
  • Favoritos: 0

Dificultad

Moderado

Pasos

6

Tiempo Requerido

10 minutos

Secciones

1

Banderas

0

Introducción

Is your power cord frayed or damaged? Follow this guide to replace it.

  1. Insert the back of a plastic opening tool into one of the beater holes Apply force to pull the circular plastic part off.

    • Insert the back of a plastic opening tool into one of the beater holes

    • Apply force to pull the circular plastic part off.

    • If necessary, use the other side of the plastic opening tool to pry the circular plastic part off.

    Editar

  2. Use a plastic opening tool to remove the speed knob. Pop up the panel with a plastic opening tool. Use a plastic opening tool to pry the white plastic switch assembly out.

    • Use a plastic opening tool to remove the speed knob.

    • Pop up the panel with a plastic opening tool.

    • Use a plastic opening tool to pry the white plastic switch assembly out.

    Editar

  3. SALTEA LA ACTUALIZACIÓN

    Ahorra reparando con un kit todo en uno.

    Compra Kits de Reparación

    SALTEA LA ACTUALIZACIÓN

    Ahorra reparando con un kit todo en uno.

    Compra Kits de Reparación

  4. Use a Phillips 2 screwdriver to remove the two 20.0mm screws that hold the bottom plastic piece. Your screwdriver may not be long or narrow enough to reach the screws in these holes. If that's the case, use another screwdriver.

    • Use a Phillips 2 screwdriver to remove the two 20.0mm screws that hold the bottom plastic piece.

    • Your screwdriver may not be long or narrow enough to reach the screws in these holes. If that's the case, use another screwdriver.

    • Remove the bottom plastic piece using a plastic opening tool.

    Editar

  5. Using a Phillips 2 screwdriver, remove the three 20.0mm screws holding the motor assembly in place. Use your hands to remove the motor assembly and circuit board. Use your hands to remove the motor assembly and circuit board.

    • Using a Phillips 2 screwdriver, remove the three 20.0mm screws holding the motor assembly in place.

    • Use your hands to remove the motor assembly and circuit board.

    Editar

  6. Firmly grip the circuit board, and using pliers, remove the black and white power cord connectors from the circuit board. Some force may be required. Be careful not to cut yourself on any electrical components. Some force may be required. Be careful not to cut yourself on any electrical components.

    • Firmly grip the circuit board, and using pliers, remove the black and white power cord connectors from the circuit board.

    • Some force may be required. Be careful not to cut yourself on any electrical components.

    Editar

  7. Using a plastic opening tool, remove the white plastic clip on the inside of the bottom plastic piece. Once it's loose, remove it with your fingers. Pull the power cord through the hole.

    • Using a plastic opening tool, remove the white plastic clip on the inside of the bottom plastic piece.

    • Once it's loose, remove it with your fingers.

    • Pull the power cord through the hole.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 3 otros colaboradores

Brad Daniels

Miembro Desde 10/02/16

537 Reputación

3 Guías creadas

Insignias: 10

+ 7 más insignias

Equipo

USF Tampa, Team 2-3, Sullivan Spring 2016 Miembro de USF Tampa, Team 2-3, Sullivan Spring 2016

USFT-SULLIVAN-S16S2G3

3 Miembros

4 Guías creadas

0 comentarios

Agregar un comentario

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 9

Ultimos 30 días: 43

Todo El Tiempo: 1,895