Repara tus cosas Comunidad Tienda

Kingston HyperX Cloud II Microphone Wire Repair

Introducción

If your Kingston HyperX Cloud II microphone is having connection issues, use this guide to replace or reconnect your microphone wire to the driver. Inside the driver, the red wire is the wire that must be soldered to the driver for the microphone to be repaired. This problem occurs when the red wire gets disconnected from the speaker or stops working from natural causes.

Qué necesitas

  1. Kingston HyperX Cloud II Microphone Wire Repair, Kingston HyperX Cloud II Microphone Wire Repair: paso 1, imagen 1 de 1

    • Pulling along the edges, take off the padding.

    Editar

  2. Kingston HyperX Cloud II Microphone Wire Repair: paso 2, imagen 1 de 2 Kingston HyperX Cloud II Microphone Wire Repair: paso 2, imagen 2 de 2

    • Use a Phillips #0 screwdriver to remove the two 11 mm screws from the bracket support.

    Editar

  3. Kingston HyperX Cloud II Microphone Wire Repair: paso 3, imagen 1 de 3 Kingston HyperX Cloud II Microphone Wire Repair: paso 3, imagen 2 de 3 Kingston HyperX Cloud II Microphone Wire Repair: paso 3, imagen 3 de 3

    • Remove the inside bracket support and then remove the outside bracket support. Then set it to the side.

    • After removing the bracket support. Expand and remove the microphone speaker from the frame.

    Editar

  5. Kingston HyperX Cloud II Microphone Wire Repair: paso 4, imagen 1 de 3 Kingston HyperX Cloud II Microphone Wire Repair: paso 4, imagen 2 de 3 Kingston HyperX Cloud II Microphone Wire Repair: paso 4, imagen 3 de 3

    • Use a Phillips #1 screwdriver to remove the two 7.9 mm screws from the red support attached to the microphone speaker.

    Editar

  6. Kingston HyperX Cloud II Microphone Wire Repair: paso 5, imagen 1 de 3 Kingston HyperX Cloud II Microphone Wire Repair: paso 5, imagen 2 de 3 Kingston HyperX Cloud II Microphone Wire Repair: paso 5, imagen 3 de 3

    • Separate the red frame support from the microphone speaker by putting it to the side.

    Editar

  7. Kingston HyperX Cloud II Microphone Wire Repair: paso 6, imagen 1 de 2 Kingston HyperX Cloud II Microphone Wire Repair: paso 6, imagen 2 de 2

    • Remove the four 11 mm screws on the speaker frame with a Phillips #2 screwdriver.

    Editar

  8. Kingston HyperX Cloud II Microphone Wire Repair: paso 7, imagen 1 de 3 Kingston HyperX Cloud II Microphone Wire Repair: paso 7, imagen 2 de 3 Kingston HyperX Cloud II Microphone Wire Repair: paso 7, imagen 3 de 3

    • Remove the microphone speaker frame.

    • Open the microphone speaker to reveal circuitry.

    • Solder the detached red wire onto the driver.

    • Be cautious not to solder the wrong wire.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 3 otros colaboradores

Daniel Olaoluwa Ajagbonna

Miembro Desde 03/27/23

325 Reputación

2 Guías creadas

Insignias: 7

+ 4 más insignias

Equipo

IUPUI, Team 1-4, Harley Spring 2023 Miembro de IUPUI, Team 1-4, Harley Spring 2023

IUPUI-HARLEY-S23S1G4

3 Miembros

3 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 8

Ultimos 30 días: 56

Todo El Tiempo: 860