Repara tus cosas Comunidad Tienda

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

Keurig K10 MINI PLUS Handle Replacement

Introducción

In this guide we will show you how to successfully remove the handle from the K-cup.

Qué necesitas

  1. Keurig K10 MINI PLUS Handle Replacement, Top Needle: paso 1, imagen 1 de 2 Keurig K10 MINI PLUS Handle Replacement, Top Needle: paso 1, imagen 2 de 2

    • Remove two 9 mm Phillips #1 screws.

    • Avoid the top needle if at all possible. The needle may cut you and/or penetrate your skin.

    • The screws are located on the top of where the K-Cup would be.

    Traducir

  2. Keurig K10 MINI PLUS Handle Replacement: paso 2, imagen 1 de 3 Keurig K10 MINI PLUS Handle Replacement: paso 2, imagen 2 de 3 Keurig K10 MINI PLUS Handle Replacement: paso 2, imagen 3 de 3

    • Once you remove the screws, the top cover should come out.

    • You will then want to remove these screws which are the same size.

    • The needle is sharp, so be careful.

    Traducir

  3. Keurig K10 MINI PLUS Handle Replacement: paso 3, imagen 1 de 1

    • Once you get those removed, you are going to want to pull on the hose until it pops off.

    • Once the hose comes off, the needle will fall out by itself.

    • Be careful when picking up the needle as the needle is sharp.

    Traducir

  5. Keurig K10 MINI PLUS Handle Replacement, Handle: paso 4, imagen 1 de 1

    • Remove the two Phillips #1 screws.

    • The top needle is intact and there, so be careful when in this area.

    Traducir

  6. Keurig K10 MINI PLUS Handle Replacement: paso 5, imagen 1 de 2 Keurig K10 MINI PLUS Handle Replacement: paso 5, imagen 2 de 2

    • Next, after the removal of the hose on the top by simply pulling it off, remove the following four Phillips #1 screws.

    Traducir

  7. Keurig K10 MINI PLUS Handle Replacement: paso 6, imagen 1 de 1

    • Once you take off the screws, this part of the handle will come off.

    Traducir

  8. Keurig K10 MINI PLUS Handle Replacement: paso 7, imagen 1 de 1

    • To pull this part off, pull inwards with the these tabs located on both sides of the handle assembly.

    Traducir

  9. Keurig K10 MINI PLUS Handle Replacement: paso 8, imagen 1 de 3 Keurig K10 MINI PLUS Handle Replacement: paso 8, imagen 2 de 3 Keurig K10 MINI PLUS Handle Replacement: paso 8, imagen 3 de 3

    • Next, remove these two Phillips #1 screws to allow the release of the actual handle from the frame.

    • For the O rings, we used the plastic prying tools. Just keep in mind that you might want to hold one side of the O ring down while trying to pry off the other side with the other.

    • Once you get the O rings on both sides out, you can pull the handle by pulling on each side.

    Traducir

  10. Keurig K10 MINI PLUS Handle Replacement: paso 9, imagen 1 de 1

    • Once you pull both sides, the handle will come off as shown.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 3 otros colaboradores

Roberto Maldonado

Miembro Desde 02/04/16

395 Reputación

1 Guía escrita

Insignias: 14

+ 11 más insignias

Equipo

iFixit, Team 1-1, Weber Winter 2016 Miembro de iFixit, Team 1-1, Weber Winter 2016

FIX-WEBER-W16S1G1

4 Miembros

37 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 4

Ultimos 30 días: 15

Todo El Tiempo: 2,275