Repara tus cosas Comunidad Tienda

Kenwood DNX571HD LCD Touch Screen Replacement

Introducción

If your screen has been damaged and needs to be replaced, this guide will provide the steps to remove the old screen and replace it with a new one.

Qué necesitas

  1. Kenwood DNX571HD LCD Touch Screen Replacement, LCD Touch Screen: paso 1, imagen 1 de 2 Kenwood DNX571HD LCD Touch Screen Replacement, LCD Touch Screen: paso 1, imagen 2 de 2

    • Turn off the stereo and remove from the vehicle before starting.

    • Unscrew the four 3.5mm side screws with a Phillips #1 screwdriver.

    • There are two screws per side.

    Editar

  2. Kenwood DNX571HD LCD Touch Screen Replacement: paso 2, imagen 1 de 3 Kenwood DNX571HD LCD Touch Screen Replacement: paso 2, imagen 2 de 3 Kenwood DNX571HD LCD Touch Screen Replacement: paso 2, imagen 3 de 3

    • Use a spudger to unhook the plastic clips on the sides and top of the front panel. There are two clips on each side and one clip on the top.

    • Place the spudger between the plastic tab and the metal case and gently lift the spudger away from the case.

    Editar

  3. Kenwood DNX571HD LCD Touch Screen Replacement: paso 3, imagen 1 de 1

    • Pull the top of the front panel out and down to remove front panel.

    • Remove the front panel gently so as not to damage the ribbon cables behind it.

    Editar

  4. Kenwood DNX571HD LCD Touch Screen Replacement: paso 4, imagen 1 de 2 Kenwood DNX571HD LCD Touch Screen Replacement: paso 4, imagen 2 de 2

    • Flip up the black clasp with the spudger to disconnect the small white ribbon cable from the main board.

    Editar

  5. Kenwood DNX571HD LCD Touch Screen Replacement: paso 5, imagen 1 de 2 Kenwood DNX571HD LCD Touch Screen Replacement: paso 5, imagen 2 de 2

    • Flip up the black clasp with the spudger to disconnect the large white ribbon cable from the main board.

    Editar

  7. Kenwood DNX571HD LCD Touch Screen Replacement: paso 6, imagen 1 de 2 Kenwood DNX571HD LCD Touch Screen Replacement: paso 6, imagen 2 de 2

    • Flip up the black clasp with the spudger to disconnect the small white ribbon cable from the vertical board.

    • Carefully pull the ribbon from the clasp with the spudger.

    Editar

  8. Kenwood DNX571HD LCD Touch Screen Replacement: paso 7, imagen 1 de 2 Kenwood DNX571HD LCD Touch Screen Replacement: paso 7, imagen 2 de 2

    • Flip up the black clasp with the spudger to disconnect the large orange ribbon cable from the main board.

    • Carefully pull the ribbon from the clasp with the spudger.

    Editar

  9. Kenwood DNX571HD LCD Touch Screen Replacement: paso 8, imagen 1 de 2 Kenwood DNX571HD LCD Touch Screen Replacement: paso 8, imagen 2 de 2

    • Push out the black clasp with the spudger to disconnect the small orange ribbon cable from the main board.

    • Gently push the ribbon out of the clasp with the spudger.

    Editar

  10. Kenwood DNX571HD LCD Touch Screen Replacement: paso 9, imagen 1 de 2 Kenwood DNX571HD LCD Touch Screen Replacement: paso 9, imagen 2 de 2

    • Using a pair of tweezers, gently pull up on the connector for the power cable to disconnect it from the main board.

    Editar

  11. Kenwood DNX571HD LCD Touch Screen Replacement: paso 10, imagen 1 de 2 Kenwood DNX571HD LCD Touch Screen Replacement: paso 10, imagen 2 de 2

    • Unscrew the two 4mm screws holding down the board that is standing vertically with a Phillips #1 screwdriver.

    • Pull up on the board to remove it.

    Editar

  12. Kenwood DNX571HD LCD Touch Screen Replacement: paso 11, imagen 1 de 2 Kenwood DNX571HD LCD Touch Screen Replacement: paso 11, imagen 2 de 2

    • Unscrew the four 5.5mm screws with a JIS #00 screwdriver.

    • Unscrew the 4mm screw with a Phillips #1 screwdriver.

    • Remove the disconnected circuit board.

    Editar

  13. Kenwood DNX571HD LCD Touch Screen Replacement: paso 12, imagen 1 de 2 Kenwood DNX571HD LCD Touch Screen Replacement: paso 12, imagen 2 de 2

    • Unscrew the four 4mm screws on the main board with a Phillips #1 screwdriver.

    • Gently lift the board out of the casing.

    • Unscrew the 5.5mm screw on the metal plate with a JIS #00 screwdriver.

    Editar

  14. Kenwood DNX571HD LCD Touch Screen Replacement: paso 13, imagen 1 de 1

    • Carefully remove the tape attaching the power cable to the metal plate.

    Editar

  15. Kenwood DNX571HD LCD Touch Screen Replacement: paso 14, imagen 1 de 2 Kenwood DNX571HD LCD Touch Screen Replacement: paso 14, imagen 2 de 2

    • Use the spudger to unhook the metal tabs and detach the metal plate from the plastic housing.

    • Place the spudger between the metal tab and the plastic case and gently lift the spudger away from the case.

    Editar

  16. Kenwood DNX571HD LCD Touch Screen Replacement: paso 15, imagen 1 de 2 Kenwood DNX571HD LCD Touch Screen Replacement: paso 15, imagen 2 de 2

    • Gently press the front of the screen to detach it from the plastic housing.

    • When removing the screen, gently flex out the plastic housing to help get the display past the plastic latch.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

4 personas más completaron esta guía.

Autor

con 5 otros colaboradores

Wendy Zaballos

Miembro Desde 09/17/18

952 Reputación

6 Guías creadas

Insignias: 8

+ 5 más insignias

Equipo

Washington State, Team S1-G1, Hope Fall 2018 Miembro de Washington State, Team S1-G1, Hope Fall 2018

WSU-HOPE-F18S1G1

4 Miembros

6 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 8

Ultimos 30 días: 69

Todo El Tiempo: 9,192