Repara tus cosas Comunidad Tienda

Kenwood DNX571HD GPS Antenna Connection Replacement

Introducción

If you are having difficulties with the Kenwood DNX571HD GPS functions, the antenna may be faulty. Follow this guide to replace it.

Qué necesitas

  1. Kenwood DNX571HD GPS Antenna Connection Replacement, CD/DVD Drive: paso 1, imagen 1 de 2 Kenwood DNX571HD GPS Antenna Connection Replacement, CD/DVD Drive: paso 1, imagen 2 de 2

    • Unscrew the four 3.5mm side screws with a Phillips #1 screwdriver.

    • There are two screws per side.

    Editar

  2. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 2, imagen 1 de 3 Kenwood DNX571HD GPS Antenna Connection Replacement: paso 2, imagen 2 de 3 Kenwood DNX571HD GPS Antenna Connection Replacement: paso 2, imagen 3 de 3

    • Use a spudger to unhook the plastic clips on the sides and top of the front panel. There are two clips on each side and one clip on the top.

    • Place the spudger between the plastic tab and the metal case and gently lift the spudger away from the case.

    Editar

  3. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 3, imagen 1 de 1

    • Pull the top of the front panel out and down to remove front panel.

    • Remove the front panel gently so as not to damage the ribbon cables behind it.

    Editar

  4. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 4, imagen 1 de 3 Kenwood DNX571HD GPS Antenna Connection Replacement: paso 4, imagen 2 de 3 Kenwood DNX571HD GPS Antenna Connection Replacement: paso 4, imagen 3 de 3

    • Unscrew the three 5mm screws from the top of the device using a Phillips #1 screwdriver.

    • Lift up to remove the top casing.

    Editar

  5. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 5, imagen 1 de 1

    • Lift the CD drive carefully to expose the attached cable underneath.

    Editar

  6. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 6, imagen 1 de 2 Kenwood DNX571HD GPS Antenna Connection Replacement: paso 6, imagen 2 de 2

    • Flip up the black clasp with a spudger to disconnect the large white ribbon cable connecting the CD drive to the board underneath.

    Editar

  7. Kenwood DNX571HD GPS Antenna Connection Replacement, Cooling Fan: paso 7, imagen 1 de 1
    Herramienta utilizada en este paso:
    Tweezers
    $4.99
    Comprar

    • Carefully unplug the fan power cord with the tweezers.

    Editar

  9. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 8, imagen 1 de 2 Kenwood DNX571HD GPS Antenna Connection Replacement: paso 8, imagen 2 de 2

    • Unscrew the three 5mm length screws with the Phillips #1 screwdriver.

    • Remove the metal plate

    • Removing the plate will damage the heat sink compound. This will need to be replaced during reassembly.

    Editar

  10. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 9, imagen 1 de 2 Kenwood DNX571HD GPS Antenna Connection Replacement: paso 9, imagen 2 de 2

    • Unscrew the three 5.5mm long screws with a Phillips #1 screwdriver.

    Editar

  11. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 10, imagen 1 de 3 Kenwood DNX571HD GPS Antenna Connection Replacement: paso 10, imagen 2 de 3 Kenwood DNX571HD GPS Antenna Connection Replacement: paso 10, imagen 3 de 3

    • Remove the four 5.5mm screws with the Phillips #1 screwdriver.

    Editar

  12. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 11, imagen 1 de 1

    • Lift the top part of the unit up from the lower chassis.

    Editar

  13. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 12, imagen 1 de 2 Kenwood DNX571HD GPS Antenna Connection Replacement: paso 12, imagen 2 de 2

    • Remove the two 13mm long screws with a Phillips #1 screwdriver.

    • Gently thread the power cable through the circuit boards to separate the fan from the body of the stereo.

    Editar

  14. Kenwood DNX571HD GPS Antenna Connection Replacement, GPS Antenna Connection: paso 13, imagen 1 de 2 Kenwood DNX571HD GPS Antenna Connection Replacement, GPS Antenna Connection: paso 13, imagen 2 de 2

    • Using a spudger, undo the clasp to disconnect the large white ribbon cable.

    Editar

  15. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 14, imagen 1 de 1

    • Remove the 5mm screw with teeth from the casing with a Phillips #1 screwdriver.

    Editar

  16. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 15, imagen 1 de 1

    • Remove the four 5mm screws with a Phillips #1 screwdriver.

    Editar

  17. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 16, imagen 1 de 2 Kenwood DNX571HD GPS Antenna Connection Replacement: paso 16, imagen 2 de 2

    • Remove the 5.5mm screw from the HDMI cable cover using a Phillips #2 screwdriver.

    Editar

  18. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 17, imagen 1 de 1

    • Remove the 5mm screw with a Phillips #1 screwdriver.

    Editar

  19. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 18, imagen 1 de 2 Kenwood DNX571HD GPS Antenna Connection Replacement: paso 18, imagen 2 de 2

    • Remove the two 5.5mm screws from the back.

    • Lift the upper portion of the stereo free from the chassis.

    Editar

  20. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 19, imagen 1 de 2 Kenwood DNX571HD GPS Antenna Connection Replacement: paso 19, imagen 2 de 2

    • Remove the two screws underneath the GPS connector.

    • Desolder the GPS connector.

    • The GPS antenna is a thru-hole-mounted device. You must apply heat to each soldered pin individually and pull them out of the holes while the solder is molten.

    • The solder material, pins, and any surrounding material will get VERY hot while melting the connections. Do not touch any metal parts during the desoldering process and give the device time to cool off once you’re finished. It may also be good to take breaks so that the electronics aren’t kept hot for extended periods of time.

    Editar

  21. Kenwood DNX571HD GPS Antenna Connection Replacement: paso 20, imagen 1 de 1

    • To remove and reinsert the connector, on the top side of the board, use your finger to gently lift the metal plate to get enough clearance.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Autor

con 3 otros colaboradores

Wendy Zaballos

Miembro Desde 09/17/18

976 Reputación

6 Guías creadas

Insignias: 8

+ 5 más insignias

Equipo

Washington State, Team S1-G1, Hope Fall 2018 Miembro de Washington State, Team S1-G1, Hope Fall 2018

WSU-HOPE-F18S1G1

4 Miembros

6 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 5

Ultimos 30 días: 7

Todo El Tiempo: 961