Menú

Tus configuraciones

Mi Mesa de Trabajo

Obtén acceso rápido a guías, partes y respuestas para tus dispositivos
Mi Carrito

Al parecer tu carrito está vacío

Visita Nuestra Tienda

Kenwood DNX571HD GPS Antenna Connection Replacement

Escrito Por: Wendy Zaballos (y 3 de otros participantes)
  • Comentarios: 0
  • Favoritos: 0

Dificultad

Difícil

Pasos

20

Tiempo Requerido

30 minutos - 2 horas

Secciones

3

Banderas

0

Introducción

If you are having difficulties with the Kenwood DNX571HD GPS functions, the antenna may be faulty. Follow this guide to replace it.

Herramientas

Comprar estas herramientas

Partes

No se requieren partes.

  1. Unscrew the four 3.5mm side screws with a Phillips #1 screwdriver. There are two screws per side.

    • Unscrew the four 3.5mm side screws with a Phillips #1 screwdriver.

    • There are two screws per side.

    Traducir

  2. Use a spudger to unhook the plastic clips on the sides and top of the front panel. There are two clips on each side and one clip on the top. Place the spudger between the plastic tab and the metal case and gently lift the spudger away from the case. Place the spudger between the plastic tab and the metal case and gently lift the spudger away from the case.

    • Use a spudger to unhook the plastic clips on the sides and top of the front panel. There are two clips on each side and one clip on the top.

    • Place the spudger between the plastic tab and the metal case and gently lift the spudger away from the case.

    Traducir

  3. Pull the top of the front panel out and down to remove front panel.

    • Pull the top of the front panel out and down to remove front panel.

    • Remove the front panel gently so as not to damage the ribbon cables behind it.

    Traducir

  4. Unscrew the three 5mm screws from the top of the device using a Phillips #1 screwdriver. Lift up to remove the top casing. Lift up to remove the top casing.

    • Unscrew the three 5mm screws from the top of the device using a Phillips #1 screwdriver.

    • Lift up to remove the top casing.

    Traducir

  5. Lift the CD drive carefully to expose the attached cable underneath.

    • Lift the CD drive carefully to expose the attached cable underneath.

    Traducir

  6. Flip up the black clasp with a spudger to disconnect the large white ribbon cable connecting the CD drive to the board underneath. Flip up the black clasp with a spudger to disconnect the large white ribbon cable connecting the CD drive to the board underneath.

    • Flip up the black clasp with a spudger to disconnect the large white ribbon cable connecting the CD drive to the board underneath.

    Traducir

  7. Carefully unplug the fan power cord with the tweezers.

    • Carefully unplug the fan power cord with the tweezers.

    Traducir

  8. ¡Envío gratuito para todos los pedidos de más de USD100 o que contengan un Pro Tech Toolkit!

    Visita Nuestra Tienda

  9. Unscrew the three 5mm length screws with the Phillips #1 screwdriver. Remove the metal plate

    • Unscrew the three 5mm length screws with the Phillips #1 screwdriver.

    • Remove the metal plate

    • Removing the plate will damage the heat sink compound. This will need to be replaced during reassembly.

    Traducir

  10. Unscrew the three 5.5mm long screws with a Phillips #1 screwdriver. Unscrew the three 5.5mm long screws with a Phillips #1 screwdriver.

    • Unscrew the three 5.5mm long screws with a Phillips #1 screwdriver.

    Traducir

  11. Remove the four 5.5mm screws with the Phillips #1 screwdriver. Remove the four 5.5mm screws with the Phillips #1 screwdriver. Remove the four 5.5mm screws with the Phillips #1 screwdriver.

    • Remove the four 5.5mm screws with the Phillips #1 screwdriver.

    Traducir

  12. Lift the top part of the unit up from the lower chassis.

    • Lift the top part of the unit up from the lower chassis.

    Traducir

  13. Remove the two 13mm long screws with a Phillips #1 screwdriver. Gently thread the power cable through the circuit boards to separate the fan from the body of the stereo.

    • Remove the two 13mm long screws with a Phillips #1 screwdriver.

    • Gently thread the power cable through the circuit boards to separate the fan from the body of the stereo.

    Traducir

  14. Using a spudger, undo the clasp to disconnect the large white ribbon cable. Using a spudger, undo the clasp to disconnect the large white ribbon cable.

    • Using a spudger, undo the clasp to disconnect the large white ribbon cable.

    Traducir

  15. Remove the 5mm screw with teeth from the casing with a Phillips #1 screwdriver.

    • Remove the 5mm screw with teeth from the casing with a Phillips #1 screwdriver.

    Traducir

  16. Remove the four 5mm screws with a Phillips #1 screwdriver.

    • Remove the four 5mm screws with a Phillips #1 screwdriver.

    Traducir

  17. Remove the 5.5mm screw from the HDMI cable cover using a Phillips #2 screwdriver. Remove the 5.5mm screw from the HDMI cable cover using a Phillips #2 screwdriver.

    • Remove the 5.5mm screw from the HDMI cable cover using a Phillips #2 screwdriver.

    Traducir

  18. Remove the 5mm screw with a Phillips #1 screwdriver.

    • Remove the 5mm screw with a Phillips #1 screwdriver.

    Traducir

  19. Remove the two 5.5mm screws from the back. Lift the upper portion of the stereo free from the chassis.

    • Remove the two 5.5mm screws from the back.

    • Lift the upper portion of the stereo free from the chassis.

    Traducir

  20. Remove the two screws underneath the GPS connector. Desolder the GPS connector.

    • Remove the two screws underneath the GPS connector.

    • Desolder the GPS connector.

    • The GPS antenna is a thru-hole-mounted device. You must apply heat to each soldered pin individually and pull them out of the holes while the solder is molten.

    • The solder material, pins, and any surrounding material will get VERY hot while melting the connections. Do not touch any metal parts during the desoldering process and give the device time to cool off once you’re finished. It may also be good to take breaks so that the electronics aren’t kept hot for extended periods of time.

    Traducir

  21. To remove and reinsert the connector, on the top side of the board, use your finger to gently lift the metal plate to get enough clearance.

    • To remove and reinsert the connector, on the top side of the board, use your finger to gently lift the metal plate to get enough clearance.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 3 otros colaboradores

Wendy Zaballos

Miembro Desde 17/09/18

838 Reputación

6 Guías creadas

Insignias: 4

+1 mas insignia

Equipo

Washington State, Team S1-G1, Hope Fall 2018 Miembro de Washington State, Team S1-G1, Hope Fall 2018

WSU-HOPE-F18S1G1

4 Miembros

6 Guías creadas

0 Comentarios

Agregar un comentario
Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 6

Todo El Tiempo: 94