Saltar al contenido principal

Introducción

This guide will offer sound advice to help you remove and replace your JBL Xtreme's speakers.

  1. Locate the seams next to the 'feet' on the bottom side of the device.
    • Locate the seams next to the 'feet' on the bottom side of the device.

  2. Use the metal spudger to gently pry and lift the edge of the seam. The cover is held in place with plastic snaps that will make a popping noise when disengaged. !!Start with the back half, this will expose TWO Screws that need to be removed before lifting the front half. Use the metal spudger to gently pry and lift the edge of the seam. The cover is held in place with plastic snaps that will make a popping noise when disengaged. !!Start with the back half, this will expose TWO Screws that need to be removed before lifting the front half.
    • Use the metal spudger to gently pry and lift the edge of the seam. The cover is held in place with plastic snaps that will make a popping noise when disengaged. !!Start with the back half, this will expose TWO Screws that need to be removed before lifting the front half.

    Start with the back half, this will expose TWO Screws that need to be removed before lifting the front half.

    MrMindlink - Contestar

    Yes, the fact needs to be added that two screws need to also be removed to get the cover off. One side snaps off but the other is attached with two screws.

    Terry Kraft - Contestar

    %#*@^@. I ripped the plastic things apart. Should have red the comments first. &&^&.

    brobarongg - Contestar

    same here ;D just grabbed some glue and hope it will stick :D

    Patrick Tippner -

  3. For the first part of the case: gently pull back the edges of the case rotating along the hinge opposite the opening seam illustrated in the second photo. Plastic snaps hold the cover in place. For the second part of the case: there are 2 screws to be removed at the seam. Once removed, the case will come off completely without forcing.
    • For the first part of the case: gently pull back the edges of the case rotating along the hinge opposite the opening seam illustrated in the second photo. Plastic snaps hold the cover in place.

    • For the second part of the case: there are 2 screws to be removed at the seam. Once removed, the case will come off completely without forcing.

    Hello Where can I get a replacement cover?? Mine is damaged.

    juan.rey19 - Contestar

    Did u ever find it they sell the covers?

    jorgetovar698 -

    Careful with this step, my JBL Xtreme case was also held in place by wo little srews !

    Arthur Lecharny - Contestar

    It feels like you are “breaking” the cover, but in fact it seems to have a kind of “bending point” near the top of the cover by the exterior controls. Watch for the two screws to remove.

    Terry Kraft - Contestar

    There is two screws holding the cover at its other end beside the plastic snaps

    Nader Belaid - Contestar

    %#*@! broke one of the little snaps near the 2 screws. still holds tight though.. be careful when pulling them out. Also, don’t forget the screws

    Mike - Contestar

  4. Unscrew the six 9.75mm Phillips head screws holding the bass radiator in place. Three of the five outer screws are indicated in the first image and the sixth inner screw is indicated in the second image. Three of the five outer screws are indicated in the first image and the sixth inner screw is indicated in the second image.
    • Unscrew the six 9.75mm Phillips head screws holding the bass radiator in place.

    • Three of the five outer screws are indicated in the first image and the sixth inner screw is indicated in the second image.

    This was the most difficult part for me. The screws are pretty tight, I needed a larger screwdriver to get them out.

    Terry Kraft - Contestar

    Achtung, die Bassstrahler sind mit dem Gehäuse über zwei “Klebedichtungen” verbunden. Diese müssen beim Zusammenbau wieder eingebaut werden.

    Carsten Schultze-Hartmann - Contestar

  5. Once the screws have been removed, the bass radiator will easily lift free. Both radiators are identical. Repeat the above steps on the opposite radiator if necessary. Both radiators are identical. Repeat the above steps on the opposite radiator if necessary.
    • Once the screws have been removed, the bass radiator will easily lift free.

    • Both radiators are identical. Repeat the above steps on the opposite radiator if necessary.

    where can i buy these parts mate?

    troy yerbury - Contestar

    Where can I buy the bass radiators independently?

    Daryl Duliep Hernandez - Contestar

    Ich empfehlen, erst den 7. Schritt auszuführen. So kann anhand der Kabel feststellen welcher Bassstrahler entfernt werden muss!

    I would recommend to do the 7th step first. So can determine, based on the cable, which bass radiator must be removed!

    Android Robo - Contestar

    Wo kann ich den die Ersatzteile kaufen bassstrahler und ein hochtöner???

    Sven Muelle - Contestar

    Schritt sieben zuerst ist eine grandiose Idee, erspart einiges an Nerven.

    Benni Basisch - Contestar

  6. With the radiators removed, locate the ribbon cable indicated in the image. Gently unplug the cable from the motherbord.
    • With the radiators removed, locate the ribbon cable indicated in the image.

    • Gently unplug the cable from the motherbord.

  7. First, unscrew the eight 12.93mm Phillips head screws indicated in red. These screws hold the two primary speakers in place. Next, remove the four 9.75mm Phillips head screws for the two smaller speakers indicated in blue and the speakers should lift out with little effort. All speakers are connected via the single cable highlighted in the previous step.
    • First, unscrew the eight 12.93mm Phillips head screws indicated in red. These screws hold the two primary speakers in place.

    • Next, remove the four 9.75mm Phillips head screws for the two smaller speakers indicated in blue and the speakers should lift out with little effort.

    • All speakers are connected via the single cable highlighted in the previous step.

    Except the passive subwoofers on each side, I found one of the JBL logo,, outside left, subwoofer plates to be partially loose which resulted in the rattle on low frequencies. Nothing a good glue couldn’t fix.

    Marc van der Bent - Contestar

Conclusión

To reassemble your device, follow these instructions in reverse order.

12 personas más completaron esta guía.

Benny Huynh

Miembro Desde 15/02/17

1,572 Reputación

4 Guías creadas

Equipo

USF Tampa, Team 1-1, Sullivan Spring 2017 Miembro de USF Tampa, Team 1-1, Sullivan Spring 2017

USFT-SULLIVAN-S17S1G1

4 Miembros

18 Guías creadas

11 comentarios

My speaker won't hold a charge for more then 2 hours? Why is that thanks

Gil Trujillo - Contestar

where can i buy the speaker of jbl xtreme?

Jeff Cancino - Contestar

Where can I get replacement speakers for my JBL?

Luis Baca - Contestar

Where can I get s replacement speaker

etesme -

where can I get parts to fix the speaker?

Dave - Contestar

Where can i buy bass radiators for my jbl Xtreme?

Francesco Iavernaro - Contestar

were can u buy the speakers from

emmanuel walker - Contestar

My jbl extreme speaker has a power but wont play and connect only the battery light indicator is working. What can I do with this? I am dissapointed since I dont use it much

mckhell14 - Contestar

wanna sell it? if so send me an email on luduncan886@gmail.com

luduncan -

Can you purchase replacement speaker driver for JBL Xtreme anywhere ? Everywhere I am looking, they are not available or sold out.

Chandler Cook - Contestar

Where can I get replacement speakers for my JBL Extreme?

snoopy_gama - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 47

Ultimos 30 días: 202

Todo El Tiempo: 24,497