Saltar al contenido principal

JBL Xtreme Cover Disassembly

Qué necesitas

  1. JBL Xtreme Cover Disassembly, Cover: paso 1, imagen 1 de 1
    • Locate the seams next to the 'feet' on the bottom side of the device.

  2. JBL Xtreme Cover Disassembly: paso 2, imagen 1 de 2 JBL Xtreme Cover Disassembly: paso 2, imagen 2 de 2
    • Use the metal spudger to gently pry and lift the edge of the seam. The cover is held in place with plastic snaps that will make a popping noise when disengaged. !!Start with the back half, this will expose TWO Screws that need to be removed before lifting the front half.

    Start with the back half, this will expose TWO Screws that need to be removed before lifting the front half.

    MrMindlink - Contestar

    Yes, the fact needs to be added that two screws need to also be removed to get the cover off. One side snaps off but the other is attached with two screws.

    Terry Kraft - Contestar

    %#*@^@. I ripped the plastic things apart. Should have red the comments first. &&^&.

    brobarongg - Contestar

    same here ;D just grabbed some glue and hope it will stick :D

    Patrick Tippner -

    Vorsichtig die Kante hochhebel, wo der Reissverschluss ist. Da ist die Hülle gesteckt. Die andere Seite hat Schrauben die man lösen sollte. Ansonsten zerstört man zu Beginn die Befestigung der einen Seite.

    Roland Bürger - Contestar

  3. JBL Xtreme Cover Disassembly: paso 3, imagen 1 de 2 JBL Xtreme Cover Disassembly: paso 3, imagen 2 de 2
    • For the first part of the case: gently pull back the edges of the case rotating along the hinge opposite the opening seam illustrated in the second photo. Plastic snaps hold the cover in place.

    • For the second part of the case: there are 2 screws to be removed at the seam. Once removed, the case will come off completely without forcing.

    Hello Where can I get a replacement cover?? Mine is damaged.

    juan.rey19 - Contestar

    Did u ever find it they sell the covers?

    jorgetovar698 -

    Careful with this step, my JBL Xtreme case was also held in place by wo little srews !

    Arthur Lecharny - Contestar

    It feels like you are “breaking” the cover, but in fact it seems to have a kind of “bending point” near the top of the cover by the exterior controls. Watch for the two screws to remove.

    Terry Kraft - Contestar

    There is two screws holding the cover at its other end beside the plastic snaps

    Nader Belaid - Contestar

    %#*@! broke one of the little snaps near the 2 screws. still holds tight though.. be careful when pulling them out. Also, don’t forget the screws

    Mike - Contestar

    Die beiden Schrauben befinden sich jeweils neben den Füßen des Geräts. (Ein Foto von den beiden Schrauben wäre sehr hilfreich!)

    RTFM - Contestar

Conclusión

To reassemble your device, follow these instructions in reverse order.

14 personas más completaron esta guía.

Benny Huynh

Miembro Desde 02/15/17

1,914 Reputación

4 Guías creadas

Equipo

USF Tampa, Team 1-1, Sullivan Spring 2017 Miembro de USF Tampa, Team 1-1, Sullivan Spring 2017

USFT-SULLIVAN-S17S1G1

4 Miembros

27 Guías creadas

5 comentarios

Can you fix my cover on speaker

c_pg08 - Contestar

where can I find a new cover for xtreme 2, if possible in black?

vale0501 - Contestar

If you find a place to buy a cover let me know

abjayaman -

you forgot about 2 screws

Enescu Catalin - Contestar

zapomniałeś o śrubach osoby które o tym mogły nie wiedzieć mogły urwać plastikowy haczyk który utrzymuje przód

megakacper11 - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 9

Ultimos 7 días: 49

Ultimos 30 días: 199

Todo El Tiempo: 30,227