Repara tus cosas Comunidad Tienda

JBL Pulse 3 Speaker Replacement

Introducción

There are four speakers located on the base of the JBL Pulse 3 under the speaker grill.

Qué necesitas

  1. JBL Pulse 3 Speaker Replacement, Speaker Grill: paso 1, imagen 1 de 1

    • Lay the JBL Pulse 3 on its side as shown in the picture.

    • Use a plastic opening tool to lift the top right corner of the speaker grill. A small amount of force is necessary to remove the grill.

    Traducir

  2. JBL Pulse 3 Speaker Replacement: paso 2, imagen 1 de 1

    • Repeat step 1 for bottom right corner of speaker grill.

    Traducir

  3. JBL Pulse 3 Speaker Replacement: paso 3, imagen 1 de 2 JBL Pulse 3 Speaker Replacement: paso 3, imagen 2 de 2

    • After pulling the right side of the grill off, place thumb underneath grill as shown in the picture.

    • Lift and pull straight out to pull grill off the posts.

    Traducir

    • Repeat steps 1-3 for the left side of the speaker grill on the JBL Pulse 3. The speaker grill should now be completely removed from the JBL Pulse 3.

    Traducir

  5. JBL Pulse 3 Speaker Replacement, Outside Casing: paso 5, imagen 1 de 2 JBL Pulse 3 Speaker Replacement, Outside Casing: paso 5, imagen 2 de 2

    • Use a Phillips #00 screwdriver to remove the six black 6mm screws on the inside of the top of the bottom section.

    Traducir

    #00 not required, successfully opened with PH#1

    Stephen Hoefler - Contestar

  6. JBL Pulse 3 Speaker Replacement: paso 6, imagen 1 de 2 JBL Pulse 3 Speaker Replacement: paso 6, imagen 2 de 2

    • Turn the JBL Pulse 3 right-side up and unscrew the top ring of the device. A small amount of force and/or a cotton cloth may be necessary to remove this piece.

    Traducir

    Ca I Specifically buy the top ring

    Julian Cruz - Contestar

    I've the same concern as the comment above, can I buy the top ring separately?

    Yousef - Contestar

    Opening is not as simple as demonstrated in Step 6. I have followed everything through, am I missing something?

    Kusala Kumsinda - Contestar

    Is there any other place to get this part? It doesnt ship to the UK

    Amelia - Contestar

  8. JBL Pulse 3 Speaker Replacement: paso 7, imagen 1 de 2 JBL Pulse 3 Speaker Replacement: paso 7, imagen 2 de 2

    • Remove the six 5mm screws on top of the JBL Pulse 3 with a Phillips #0 screwdriver.

    Traducir

  9. JBL Pulse 3 Speaker Replacement: paso 8, imagen 1 de 1

    • Pull off the top disc of the JBL Pulse 3.

    Traducir

  10. JBL Pulse 3 Speaker Replacement: paso 9, imagen 1 de 2 JBL Pulse 3 Speaker Replacement: paso 9, imagen 2 de 2

    • Remove the five 7mm screws on the inside of the JBL Pulse 3 with a Phillips #1 screwdriver.

    Traducir

    This phase could be difficult. Try to “twist” the speaker to have a little gap between both parts and insert gently a screwdriver or opening toile to spread the gap.

    Richard Devos - Contestar

  11. JBL Pulse 3 Speaker Replacement: paso 10, imagen 1 de 2 JBL Pulse 3 Speaker Replacement: paso 10, imagen 2 de 2

    • Peel off black, taped-on electrical lead from the inside side of the JBL Pulse 3.

    Traducir

  12. JBL Pulse 3 Speaker Replacement: paso 11, imagen 1 de 1

    • Pull the top section of the JBL Pulse 3 up. The outside casing to the JBL Pulse 3 should now be removed.

    Traducir

  13. JBL Pulse 3 Speaker Replacement, LED Light Display: paso 12, imagen 1 de 3 JBL Pulse 3 Speaker Replacement, LED Light Display: paso 12, imagen 2 de 3 JBL Pulse 3 Speaker Replacement, LED Light Display: paso 12, imagen 3 de 3

    • Use a Phillips #2 screwdriver to remove the six 11 mm screws that circle the bottom of the LED light display.

    • Pull the LED light display off of the JBL Pulse 3 base.

    Traducir

  14. JBL Pulse 3 Speaker Replacement: paso 13, imagen 1 de 2 JBL Pulse 3 Speaker Replacement: paso 13, imagen 2 de 2

    • Use tweezers to pull the five connections off of the LED light display.

    Traducir

    up to step 13, the battery replacement steps are the same.
    From step 14 the steps change.
    Very good instructions for changing the battery in the jbl pulse 3 can be found here:

    https://www.youtube.com/watch?v=MpznDgxg...

    Mike Miker - Contestar

  15. JBL Pulse 3 Speaker Replacement, Motherboard: paso 14, imagen 1 de 2 JBL Pulse 3 Speaker Replacement, Motherboard: paso 14, imagen 2 de 2

    • Using a Phillips #0 screwdriver, remove the two black 8mm screws on the bottom of the LED light display.

    Traducir

  16. JBL Pulse 3 Speaker Replacement: paso 15, imagen 1 de 3 JBL Pulse 3 Speaker Replacement: paso 15, imagen 2 de 3 JBL Pulse 3 Speaker Replacement: paso 15, imagen 3 de 3

    • Pull out the motherboard slightly from the LED light display as shown. Using tweezers, unplug the three connections attached to the motherboard.

    Traducir

  17. JBL Pulse 3 Speaker Replacement: paso 16, imagen 1 de 1

    • Pull the rest of the motherboard out from the LED light display.

    • Using wire cutters, snip the black wire connecting to the base of the JBL Pulse 3 at the base of the motherboard. The motherboard should now be removed from the JBL Pulse 3.

    Traducir

    Hi Guys! Thanks a lot for the tutorial, but anyone knows where THIS BLACK WIRE IS CONNECTED at the base of the speaker? I accidentally remove it..

    caiopeluso - Contestar

  18. JBL Pulse 3 Speaker Replacement, Speaker: paso 17, imagen 1 de 2 JBL Pulse 3 Speaker Replacement, Speaker: paso 17, imagen 2 de 2

    • Using a Phillips #2 screwdriver, remove the four 10mm screws on the corner of the speaker on the side of the base of the JBL Pulse 3.

    Traducir

  19. JBL Pulse 3 Speaker Replacement: paso 18, imagen 1 de 2 JBL Pulse 3 Speaker Replacement: paso 18, imagen 2 de 2

    • Pull out the speaker and cut the black and red wire with wire cutters. The speaker should now be removed from the JBL Pulse 3.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Note: To finish replacing the speaker, you must solder both wires back on to the new speaker.

2 comentarios

My speaker is making weird noises. It sounds like being crack. Do I need to replace the speaker or try to teardown to clean up the dust?

John - Contestar

Hey Mates. Tell me please, somebody knows , the size of the replacement speaker and it fit from jbl charge 3 or some models? Thanks

Seven Nes - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 4

Ultimos 30 días: 27

Todo El Tiempo: 2,395