Saltar al contenido principal

JBL On Stage II Speakers Replacement

Qué necesitas

  1. JBL On Stage II Speakers Replacement, Cracking the Case: paso 1, imagen 1 de 1
    • Turn the device upside down so that the three rubber pads are facing up.

  2. JBL On Stage II Speakers Replacement: paso 2, imagen 1 de 1
    • Use a heat gun (set to low) to apply heat to one of the rubber pads until you can easily remove the pad. This step takes around 5-7 minutes.

  3. JBL On Stage II Speakers Replacement: paso 3, imagen 1 de 1
    • Remove the heated rubber pad with a plastic opening tool.

    • Repeat steps 2 and 3 for the two remaining rubber pads.

  4. JBL On Stage II Speakers Replacement: paso 4, imagen 1 de 2 JBL On Stage II Speakers Replacement: paso 4, imagen 2 de 2
    • Remove the six 1cm T-10 torx screws on the bottom of the device (found under the rubber pads) using a T-10 Torx screwdriver.

  5. JBL On Stage II Speakers Replacement: paso 5, imagen 1 de 3 JBL On Stage II Speakers Replacement: paso 5, imagen 2 de 3 JBL On Stage II Speakers Replacement: paso 5, imagen 3 de 3
    • Open the device along its seam.

    • Be careful when separating the device because there are wires connecting the two seperate halves.

  6. JBL On Stage II Speakers Replacement: paso 6, imagen 1 de 1
    • Disconnect the ribbon cable connector from the top half of the device by pulling outward and parallel to the connecting pins.

  7. JBL On Stage II Speakers Replacement: paso 7, imagen 1 de 2 JBL On Stage II Speakers Replacement: paso 7, imagen 2 de 2
    • Locate and disconnect the two molex connectors found on either side of the ribbon cable connector on the bottom half of the device.

    Where do I find these speakers

    HighChief - Contestar

  8. JBL On Stage II Speakers Replacement, The Speakers: paso 8, imagen 1 de 2 JBL On Stage II Speakers Replacement, The Speakers: paso 8, imagen 2 de 2
    • Separate speakers from their slots using a metal spudger.

    • Careful, as this step may cause damage to the device.

  9. JBL On Stage II Speakers Replacement: paso 9, imagen 1 de 2 JBL On Stage II Speakers Replacement: paso 9, imagen 2 de 2
    • Cut the black wire (leading to the speaker you are replacing) with a pair of wire cutters.

    • Cut the red wire (leading to the speaker you are replacing) with a pair of wire cutters.

    • Notice that two black wires and two red wires connect to the speaker, be sure to reattach both wires to the new speaker.

    Where can I find the speakers for replacement just the speakers only

    HighChief - Contestar

    just pull of the plug, no need to cut the wires

    pikachu chuuu - Contestar

Conclusión

To reassemble your device, follow these directions in reverse order.

5 personas más completaron esta guía.

Equipo

Cal Poly, Team 9-28, Maness Winter 2014 Miembro de Cal Poly, Team 9-28, Maness Winter 2014

CPSU-MANESS-W14S9G28

4 Miembros

7 Guías creadas

8 comentarios

Where can I buy the replacement speaker?

Gilberto Ruiz - Contestar

I join Gןilberto question,can someone attach a link to replacement speakers or tell what is the p/n of the speakers ?

Thanks !

Oded Hafuta -

little bit late i just order it after 2 years searching

https://es.aliexpress.com/item/2pcs-For-...

Marcos Jaime - Contestar

Do these work as original driver are 8 ohm?

pikachu chuuu -

Thank you for posting this! I need to fix my speakers.

prak - Contestar

Where can i buy these speakers (3w-8 omhns)?

Euri Lore Carrion - Contestar

My JBL "on Stage III" Ipod Sound Dock with remote - World Wide Voltage speakers r all damage, i want a new spaekars, how can i get his.

Ram Chavan - Contestar

How to find these component speaker

My jbl stage 2 speaker is broke

I want to buy new ones but i did not find them

Let me know if u arrange

chandrakant - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 12

Ultimos 30 días: 46

Todo El Tiempo: 14,253