Introducción
Con esta guía, el usuario aprenderá a remover las bocinas y checar si las bocinas están funcionando de manera adecuada, además de como reemplazarlas.
Qué necesitas
-
-
Empieza por quitar las tapas de goma de ambos lados del JBL Flip 2 utilizando el spudger negro para introducirte entre los pliegues.
-
-
-
El chip NFC está pegado en el lateral del dispositivo. Utiliza el spudger negro para separar el micro de la superficie.
-
Desliza suavemente el chip NFC en el dispositivo a través de la ranura de la que sale el cable.
what if the wire DID disconnect? could s.o. add a detail pic of exactly where the cables connect on the chip?
Need the real name of the NFC chip, caus i broked and need to change
Thanks
Need the real name of the NFC chip, cause i broked and need to change
Thanks
My chip reads
WN-3088 20130912
-
-
-
Retira los dos tornillos Phillips nº 1 de 7,0 mm.
-
Retira con cuidado la cubierta de plástico plateada tirando de ambos extremos.
-
Separa la pieza de plástico plateada tirando de ella desde el centro.
Tutto molto interessante.
Ma la cosa più importante è:
Dove acquistare gli altoparlanti ??
-
-
-
-
Con el clásico spudger, metete debajo de las tiras de cinta negra que se encuentran a ambos lados del aparato.
-
Después de levantar una parte de la cinta del dispositivo, despega suavemente la cinta del dispositivo, asegurándote de mantenerla intacta.
-
Hay otro trozo de cinta adhesiva en el lado del dispositivo con los botones de control. Levanta la cinta con el spudger clásico y luego despegue el resto de la cinta.
Keeping the tape intact is impossible - I replaced it with electrical tape.
-
-
-
Utiliza el spudger negro para desconectar el cable auxiliar de su toma.
What is the function of auxi. Wire
When you plug in the audio jack it goes to the motherboard, the amplifier and then to the wire directly to the speakers.
-
-
-
Retira con cuidado el cable que conecta el chip de control a la placa base.
What's the name of the cable connecting the control chip to the motherboard
I want motherboard control chip
connecting the control chip kitne ka hai
-
-
-
Con el spudger negro, retira con cuidado el cable que conecta la batería a la placa base.
-
-
-
Checa las conexiones de la bocina para ver si está floja.
-
Si los conectores están flojos, necesitarán ser re.soldarlos. Para información de como hacerlo, click https://es.ifixit.com/Guía/Cómo+soldar+y...
-
-
-
Remueve las conexiones de las bocinas.
-
Reemplace las bocinas viejas soldando los 4 cables en cada conector de las bocinas nuevas.
https://www.highlight-led.de/en/mini-bas...
This should work. Even the bracket seems to be right.
On my JBL FLip 2 speaker’s label says:
F40N8C
HS0009-0001061
8 Ohm
PS2-150HB
As I got it is 40mm (1,5 inch) diameter.
This label is quite similar to this brand: GHXamp
On my side, I ordered the speaker PUI Audio ASX04008-R from Digikey (668-1563-ND), which is the right diameter. It is rated 3W with max 5W. The down side of this speaker is the missing center cone. Hoverver, I have been able to retreive the cone from the defective speaker and transfer it. The new speaker has an adhesive ring that allow to do this. Since the new speaker doesn't have the flanges, I have cut, with a cutter, the ones from the old speaker and be able to hold the new speaker in place. To make all my test, I have used the iPhone app "Tone Generator" made by TMSOFT which allow me to select any frequency and use the balance control to compare between the right and left speaker.
The end result is very good.
Amazon Mitteilung:
6,49 $ (3,25 $ / Stück)
Dieser Artikel kann nicht an den von dir ausgewählten Zustellungsort versendet werden. Bitte wähle einen anderen Zustellungsort aus.
In Deutschland nicht erhältlich. -
Para reensamblar tu dispositivo, sigue estas instrucciones en orden inverso.
Para reensamblar tu dispositivo, sigue estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
28 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
18 comentarios
Since I wasn’t in the US and shipping cost from the Dayton speakers were prohibitvely, I ended up finding the speakers form China. The upside is that they are easier to install, since you dont have to cut down the lateral support, the downside is that they are 6 Ohms and have a lower quality. Though I worked for me.
Hey, maybe you have the link? :)
What is the size and ohmz and watts of the speaker?
8ohms 40 watts and 1 inch I think. I been searching where to buy these as well. The rings are separated on mine
En donde puedo comprar las speaker
Instructions are very helpful and I thank you . However I now am finding it impossible to find the replacement speakers for the flip 2 so it appears the de-construction was a waste of time! Such a shame as the unit is working fine but for a buzzy speaker.
Can anyone provide a link to buy speakers please
Doe anyone know if there are any alternative for the speakers? Or the ref code for them?
I need to replace my speaker from my jbl flip ..how can I buy them
I just added a video with details on a good replacement speaker option that I used with great success. The Flip 2 sounds like new. Here’s a link to the speakers that I purchased:
I want to buy replacement speakers. Can someone share ebay.in
Its not available for indian locations.
If someone can help me to find the replacement battery? Thanks
From where i can buy these speakers?
Nitin Z - Contestar
First thing I did was rip the wire from the NFC chip! Luclily I don't need it as I only ever use my flip with my iPhone.
Ken McMahon - Contestar