Repara tus cosas Comunidad Tienda

Ivation IVWPDC20Y Lens Assembly Replacement

Introducción

This guide will show you how to replace a faulty lens unit for this camera.

Qué necesitas

  1. Ivation IVWPDC20Y Lens Assembly Replacement, Lens Assembly: paso 1, imagen 1 de 1

    • With the H2.0 bit screwdriver, remove the two screws on the yellow waterproof cover

    Editar

  2. Ivation IVWPDC20Y Lens Assembly Replacement: paso 2, imagen 1 de 1

    • Apply a plastic opening tool to each of the corners and gently remove the casing

    • The front casing is held down by adhesive and may require additional work to remove

    • Apply just enough force to undo the inner latches to make sure not to damage the waterproof seal

    Editar

  3. Ivation IVWPDC20Y Lens Assembly Replacement: paso 3, imagen 1 de 1

    • Remove the five silver screws from the inner casing using the PH00 screwdriver bit

    Editar

  4. Ivation IVWPDC20Y Lens Assembly Replacement: paso 4, imagen 1 de 1

    • Remove the six screws from the edge of the clear inner casing with the PH00 screwdriver bit

    • These screws are very small and easy to strip so apply consistent pressure when removing them

    Editar

  6. Ivation IVWPDC20Y Lens Assembly Replacement: paso 5, imagen 1 de 1

    • Pry off back outer casing using the black spudger or the blue prying tools

    Editar

  7. Ivation IVWPDC20Y Lens Assembly Replacement: paso 6, imagen 1 de 1

    • Carefully remove the screen from the silver casing using a prying tool or the black spudger

    • There is adhesive in the center of the screen, be sure not to bend it when applying pressure

    Editar

  8. Ivation IVWPDC20Y Lens Assembly Replacement: paso 7, imagen 1 de 1

    • Using the poker end of the spudger push gently on the black pegs holding the orange tape in place

    • Screen and orange tape should slip out as a whole

    Editar

  9. Ivation IVWPDC20Y Lens Assembly Replacement: paso 8, imagen 1 de 1

    • Remove three screws holding the silver screen casing to the motherboard using the PH00 bit screwdriver

    Editar

  10. Ivation IVWPDC20Y Lens Assembly Replacement: paso 9, imagen 1 de 1

    • Remove three screws holding the motherboard into the casing using the PH00 bit screwdriver

    Editar

  11. Ivation IVWPDC20Y Lens Assembly Replacement: paso 10, imagen 1 de 1

    • Gently lift the corner of the motherboard out

    • Everything should come out as one component free of the casing

    Editar

  12. Ivation IVWPDC20Y Lens Assembly Replacement: paso 11, imagen 1 de 1

    • Remove the two screws holding the lens assembly to the motherboard using the PH00 bit screwdriver

    Editar

  13. Ivation IVWPDC20Y Lens Assembly Replacement: paso 12, imagen 1 de 1

    • Remove the soldering on the 3 wires that are connected to the lens unit

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Autor

con 3 otros colaboradores

Jack Schlandt

Miembro Desde 02/08/16

197 Reputación

1 Guía escrita

Insignias: 11

+ 8 más insignias

Equipo

USF Tampa, Team 6-6, Eyestone Spring 2016 Miembro de USF Tampa, Team 6-6, Eyestone Spring 2016

USFT-EYESTONE-S16S6G6

3 Miembros

5 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 0

Todo El Tiempo: 273