Saltar al contenido principal

Insignia NS-BCDCAS1 CD Laser Lens Replacement

Qué necesitas

  1. Insignia NS-BCDCAS1 CD Laser Lens Replacement, Outer Panels: paso 1, imagen 1 de 2 Insignia NS-BCDCAS1 CD Laser Lens Replacement, Outer Panels: paso 1, imagen 2 de 2
    • Turn the boombox around to see the back, and then flip it upside down.

    • Insert a 2.5mm flathead driver into the two holes next to the battery compartment.

    • Turn the driver counterclockwise several times to loosen and pull out the 17mm screw.

  2. Insignia NS-BCDCAS1 CD Laser Lens Replacement: paso 2, imagen 1 de 1
    • Peel off the two black square foams in front of the battery compartment to reveal a screw under each one.

  3. Insignia NS-BCDCAS1 CD Laser Lens Replacement: paso 3, imagen 1 de 2 Insignia NS-BCDCAS1 CD Laser Lens Replacement: paso 3, imagen 2 de 2
    • Remove the two 8mm screws using a 2.5mm flathead driver.

    • The front grey panel will loosen up once the final screw is removed.

  4. Insignia NS-BCDCAS1 CD Laser Lens Replacement: paso 4, imagen 1 de 1
    • Turn the boombox on its back.

    • Release the front panel by pushing down on the latches holding the panels together.

    • There are four silver latches on the top side of the panel and one on the bottom.

    • Do not force the panel comletely off, there are cables attached inside.

  5. Insignia NS-BCDCAS1 CD Laser Lens Replacement: paso 5, imagen 1 de 2 Insignia NS-BCDCAS1 CD Laser Lens Replacement: paso 5, imagen 2 de 2
    • Turn the boombox around to view the back and lift the handle up.

    • Using the same driver with 2.5mm flathead, remove the two 14mm screws under the handle.

    • Gently lift the black top but do not pull completely away.

  6. Insignia NS-BCDCAS1 CD Laser Lens Replacement, CD Laser Lens: paso 6, imagen 1 de 1
    • Unplug the red and black wires from the large yellow motherboard by pulling upwards.

  7. Insignia NS-BCDCAS1 CD Laser Lens Replacement: paso 7, imagen 1 de 1
    • Unplug the thick, white and pink cord from underneath the black top by pulling downwards.

  8. Insignia NS-BCDCAS1 CD Laser Lens Replacement: paso 8, imagen 1 de 1
    • Remove the black shiny strip from both ends of the white motherboard adaptor.

  9. Insignia NS-BCDCAS1 CD Laser Lens Replacement: paso 9, imagen 1 de 1
    • Using a Phillips #0, remove the two 11mm screws attached to the green legs underneath the top panel.

  10. Insignia NS-BCDCAS1 CD Laser Lens Replacement: paso 10, imagen 1 de 1
    • With a plastic opening tool, take off the red rings on the other two green legs.

    • The red rings fall off easily once loosened.

  11. Insignia NS-BCDCAS1 CD Laser Lens Replacement: paso 11, imagen 1 de 1
    • Using a JIS 1, remove the 8mm screw on the grey, square plate.

  12. Insignia NS-BCDCAS1 CD Laser Lens Replacement: paso 12, imagen 1 de 3 Insignia NS-BCDCAS1 CD Laser Lens Replacement: paso 12, imagen 2 de 3 Insignia NS-BCDCAS1 CD Laser Lens Replacement: paso 12, imagen 3 de 3
    • Slide the silver bar out.

    • Everything will be loosened. Support it with your hand

    • The square cube with the tiny lense is loosened. Slide it down to take out of the nook.

    • Detach the black tape so the cube is completely by itself. Replace the cube with a new one.

Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Erin King

Miembro Desde 09/12/16

215 Reputación

2 Guías creadas

Equipo

CSU Fullerton, Team 2-5, Bruce Fall 2016 Miembro de CSU Fullerton, Team 2-5, Bruce Fall 2016

CSUF-BRUCE-F16S2G5

4 Miembros

4 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 6

Ultimos 30 días: 15

Todo El Tiempo: 966