Repara tus cosas Comunidad Tienda

Huawei P20 Pro Battery Disconnect

Sólo Prerrequisito
Esta guía solo debería usarse como prerrequisito para otras guías. Por tanto, estará incompleta.

Introducción

prereq only battery disconnect

Qué necesitas

  1. Huawei P20 Pro Battery Disconnect, Rear Glass Replacement: paso 1, imagen 1 de 1

    • Switch off your phone.

    • Use an iOpener to loosen the adhesive beneath the rear glass. Apply the iOpener for at least two minutes. You might want to repeat this step several times during the back cover removal.

    • The adhesive of the Huawei P20 Pro is of moderate strength, however a hair dryer, heat gun, or hot plate may also be used if you aren't able to open the device with the iOpener. Be careful not to overheat the phone—the OLED display and internal battery are both susceptible to heat damage.

    Traducir

  2. Huawei P20 Pro Battery Disconnect: paso 2, imagen 1 de 3 Huawei P20 Pro Battery Disconnect: paso 2, imagen 2 de 3 Huawei P20 Pro Battery Disconnect: paso 2, imagen 3 de 3

    • If the phone's rear glass is cracked, a suction cup may not stick very well. Try lifting it with strong tape, or superglue the suction cup in place and allow it to cure so you can proceed.

    • Press a suction cup onto the rear glass close to the bottom edge of the phone.

    • Lift the bottom edge with the suction cup, opening a slight gap between the rear glass and the frame.

    • Insert an opening pick in the gap and slide it to the bottom right corner. Leave it there to prevent the adhesive from resealing.

    Traducir

  3. Huawei P20 Pro Battery Disconnect: paso 3, imagen 1 de 2 Huawei P20 Pro Battery Disconnect: paso 3, imagen 2 de 2

    • Insert a second opening pick and slide it to the bottom left corner. Leave it there to prevent the adhesive from resealing.

    Traducir

  4. Huawei P20 Pro Battery Disconnect: paso 4, imagen 1 de 3 Huawei P20 Pro Battery Disconnect: paso 4, imagen 2 de 3 Huawei P20 Pro Battery Disconnect: paso 4, imagen 3 de 3

    • Insert a third opening pick at the bottom left corner.

    • Slide the tip of the opening pick along the left edge of the phone to cut the adhesive.

    • Leave the opening pick in the top left corner of the phone to prevent the adhesive from resealing.

    Traducir

  5. Huawei P20 Pro Battery Disconnect: paso 5, imagen 1 de 2 Huawei P20 Pro Battery Disconnect: paso 5, imagen 2 de 2

    • In case you're having trouble to cut the adhesive, reapply the iOpener for another minute to loosen it.

    • Insert a fourth opening pick at the top left corner of the phone.

    • Slide the opening pick along the upper edge of the phone to cut the adhesive beneath the rear glass and leave it in the top right corner.

    Traducir

  7. Huawei P20 Pro Battery Disconnect: paso 6, imagen 1 de 3 Huawei P20 Pro Battery Disconnect: paso 6, imagen 2 de 3 Huawei P20 Pro Battery Disconnect: paso 6, imagen 3 de 3

    • Insert a fifth opening pick at the top right corner of the rear glass.

    • Slide the opening pick along the right edge of the phone to cut the remaining adhesive.

    • Don't open the phone all the way yet. The proximity sensor flex cable is still connected to the motherboard.

    Traducir

  8. Huawei P20 Pro Battery Disconnect: paso 7, imagen 1 de 3 Huawei P20 Pro Battery Disconnect: paso 7, imagen 2 de 3 Huawei P20 Pro Battery Disconnect: paso 7, imagen 3 de 3

    • Carefully lift the rear glass until you can reach the connector of the proximity sensor flex cable next to the rear camera assembly.

    Traducir

  9. Huawei P20 Pro Battery Disconnect: paso 8, imagen 1 de 2 Huawei P20 Pro Battery Disconnect: paso 8, imagen 2 de 2

    • Use the flat end of a spudger to pry up and disconnect the proximity sensor flex cable.

    Traducir

  10. Huawei P20 Pro Battery Disconnect: paso 9, imagen 1 de 2 Huawei P20 Pro Battery Disconnect: paso 9, imagen 2 de 2

    • Remove the rear glass.

    • Before installing fresh adhesive and reassembly, remove any remaining adhesive from the phone, and clean the glued areas with isopropyl alcohol and a lint-free cloth.

    Traducir

  11. Huawei P20 Pro Battery Disconnect, Motherboard Cover and NFC: paso 10, imagen 1 de 1

    • Remove the nine Phillips #00 screws (3.4 mm length).

    Traducir

  12. Huawei P20 Pro Battery Disconnect: paso 11, imagen 1 de 3 Huawei P20 Pro Battery Disconnect: paso 11, imagen 2 de 3 Huawei P20 Pro Battery Disconnect: paso 11, imagen 3 de 3

    • Insert an opening pick under the left side of the motherboard cover that includes the NFC.

    • Slide the opening pick towards the top left corner of the phone and twist it to pry the cover out of its plastic clamps.

    Traducir

  13. Huawei P20 Pro Battery Disconnect: paso 12, imagen 1 de 2 Huawei P20 Pro Battery Disconnect: paso 12, imagen 2 de 2

    • Repeat the previous process on the right side and twist the opening pick to pry up the motherboard cover.

    Traducir

  14. Huawei P20 Pro Battery Disconnect: paso 13, imagen 1 de 1

    • Remove the motherboard cover.

    Traducir

  15. Huawei P20 Pro Battery Disconnect, Battery Disconnect: paso 14, imagen 1 de 2 Huawei P20 Pro Battery Disconnect, Battery Disconnect: paso 14, imagen 2 de 2

    • Use the flat end of a spudger to pry up and disconnect the battery flex cable.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 1 otro colaborador

Dominik Schnabelrauch

Miembro Desde 11/23/16

202,809 Reputación

682 Guías creadas

Insignias: 40

+ 37 más insignias

Equipo

iFixit Miembro de iFixit

Staff

135 Miembros

16,732 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 0

Todo El Tiempo: 62