Introducción

Brakes slow your bike down when you pull on the brake lever on the handlebar. The brake calipers are connected to the brake levers by a cable that squeezes the brake-pads that are attached to the brake calipers. When the brake pads contact the rims they slow down the rim of the wheel, slowing down the bike.

Partes

No se requieren partes.

Squeeze the calipers together, and remove the brake cable.
  • Squeeze the calipers together, and remove the brake cable.

Agregar Comentario

Loosen the break caliper bolt, and remove the brake caliper.
  • Loosen the break caliper bolt, and remove the brake caliper.

Agregar Comentario

  • Inspect the brake pad. If the pad has worn down past the “wear line”, then it needs to be replaced.

Agregar Comentario

  • Clean and lubricate the parts as necessary before reattaching the caliper arms.

  • Bolt the caliper arms back on while making sure the the pin on the back side of the caliper arm lines back up with the one of the holes in the frame. Each side should be in the same hole.

Agregar Comentario

  • Reattach the brake cable to the calipers.

Agregar Comentario

  • Loosen the brake pad bolt.

Agregar Comentario

  • Get an ordinary piece of paper, and fold it twice over.

  • Place the sheet of paper between the brake pad and the rim in the position shown.

What's the reason of doing this? Is it to keep 1 or 2 mm gap between the pad and rim or to 'toe-in' the break bad?

Seamuzzaman Nahid - Contestar

Helps to prevent brake chatter by feathering in the pads to the rim.

R I - Contestar

  • Align the brake pad so that it is flush with the rim, with no part touching the rubber of the tire.

  • Have somebody clamp down very tightly on the brakes.

  • Tighten the brake pad bolt in place.

The brake lever could also be held down with a cable tie, velcro strap, or a strong elastic band

R I - Contestar

  • Tighten/loosen the tension adjustment screws on each the caliper arm to adjust the resting distance of each brake pad, so that each pad is equally distant from the rim. Tightening the screw will shift the caliper outward from the bike, loosening it will shift it inward.

  • Tighten/loosen the brake adjuster on the handle bars such that when you clamp down on the brakes, the brake lever stops before hitting the handle bar. This will set the distance between the brake pads and the rim.

  • Tighten the lock nut on the brake adjuster to permanently set its position.

Very good!,Was wondering about some small details . This clered it out. Thx

Tim Brumen - Contestar

Linea de Meta

32 personas más completaron esta guía.

Travis Tonder

Miembro Desde 05/10/10

2,462 Reputación

5 Guías creadas

Equipo

Cal Poly, Team 5-13, Maness Fall 2010 Miembro de Cal Poly, Team 5-13, Maness Fall 2010

CPSU-MANESS-F10S5G13

4 Miembros

11 Guías creadas

[|what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? IS IT OKAY?????? IS IT OKAY??????]

Merpface - Contestar

The red bullet point seems to correspond with the red circle in the image.

Victor Chan -

help me please

Merpface - Contestar

aqswdftgyhuji

Merpface - Contestar

yyyyyaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa

Merpface - Contestar

1bn kj vgobjy

Merpface - Contestar

“what does it mean if the point is red???? “

I believe that is indicating that this step corresponds to an image which highlights a specific step. I saw this two times, in step 4 and step 9. For step 4, it shows the highlight in the second image and for step 9, the highlight is in the first image. It seems that the red bullet point is just to make it easier to map the step to the image.

Hope this helps

Tony - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 64

Últimos 7 Días: 413

Últimos 30 Días: 1,961

Todo El Tiempo: 51,026