Saltar al contenido principal

Hover-1 Titan Right Gyroscope Replacement

Qué necesitas

  1. Hover-1 Titan Right Gyroscope Replacement, Bottom Right Panel: paso 1, imagen 1 de 2 Hover-1 Titan Right Gyroscope Replacement, Bottom Right Panel: paso 1, imagen 2 de 2
    • Flip the hoverboard so the bottom is facing up.

    • The right side is the side that has the power button. There is also an "R" on the metal plate underneath the battery.

  2. Hover-1 Titan Right Gyroscope Replacement: paso 2, imagen 1 de 2 Hover-1 Titan Right Gyroscope Replacement: paso 2, imagen 2 de 2
    • Using a Phillips #1 screwdriver, remove the two 14 mm screws closest to the center of the hoverboard.

    • Using a Phillips #1 screwdriver, remove the four 12 mm screws located in the middle of the panel.

    • Using a Phillips #1 screwdriver, remove the two 15 mm screws located closest to the wheel.

  3. Hover-1 Titan Right Gyroscope Replacement: paso 3, imagen 1 de 3 Hover-1 Titan Right Gyroscope Replacement: paso 3, imagen 2 de 3 Hover-1 Titan Right Gyroscope Replacement: paso 3, imagen 3 de 3
    • Grip the bottom right panel and lift to remove it.

  4. Hover-1 Titan Right Gyroscope Replacement, Right Gyroscope and Motherboard: paso 4, imagen 1 de 2 Hover-1 Titan Right Gyroscope Replacement, Right Gyroscope and Motherboard: paso 4, imagen 2 de 2
    • Unplug the battery from the gyroscope/motherboard by holding the yellow connector and pulling apart.

  5. Hover-1 Titan Right Gyroscope Replacement: paso 5, imagen 1 de 3 Hover-1 Titan Right Gyroscope Replacement: paso 5, imagen 2 de 3 Hover-1 Titan Right Gyroscope Replacement: paso 5, imagen 3 de 3
    • Remove four 12 mm Phillips #1 head screws from the corners of the green gyroscope/motherboard.

  6. Hover-1 Titan Right Gyroscope Replacement: paso 6, imagen 1 de 2 Hover-1 Titan Right Gyroscope Replacement: paso 6, imagen 2 de 2
    • Unplug the bottom left connector by squeezing it and pulling it away from the board.

  7. Hover-1 Titan Right Gyroscope Replacement: paso 7, imagen 1 de 2 Hover-1 Titan Right Gyroscope Replacement: paso 7, imagen 2 de 2
    • Unplug the white wires by squeezing the connector and pulling away from the board.

  8. Hover-1 Titan Right Gyroscope Replacement: paso 8, imagen 1 de 2 Hover-1 Titan Right Gyroscope Replacement: paso 8, imagen 2 de 2
    • Unplug one set of the red, white, purple, and black wires by squeezing the connector and pulling away from the board.

  9. Hover-1 Titan Right Gyroscope Replacement: paso 9, imagen 1 de 2 Hover-1 Titan Right Gyroscope Replacement: paso 9, imagen 2 de 2
    • Unplug the other set of the red, white, purple, and black wires by squeezing the connector and pulling away from the board.

  10. Hover-1 Titan Right Gyroscope Replacement: paso 10, imagen 1 de 1
    • Cut the cable tie and unplug the remaining wires.

Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Jessica Ouyang

Miembro Desde 10/08/18

619 Reputación

4 Guías creadas

Equipo

Cal Poly, Team S15-G4, White Fall 2018 Miembro de Cal Poly, Team S15-G4, White Fall 2018

CPSU-WHITE-F18S15G4

4 Miembros

10 Guías creadas

Un comentario

Where can I get the circuit boards for the left and right ?

jfsucher - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 9

Ultimos 30 días: 21

Todo El Tiempo: 1,037