Saltar al contenido principal

Hover-1 Titan Left Gyroscope Replacement

Qué necesitas

  1. Hover-1 Titan Left Gyroscope Replacement, Bottom Left Panel: paso 1, imagen 1 de 2 Hover-1 Titan Left Gyroscope Replacement, Bottom Left Panel: paso 1, imagen 2 de 2
    • Flip the hoverboard so the bottom is facing up.

    • The left side is the side that has the charge port. There is also an "L" on the metal plate underneath the wires.

  2. Hover-1 Titan Left Gyroscope Replacement: paso 2, imagen 1 de 2 Hover-1 Titan Left Gyroscope Replacement: paso 2, imagen 2 de 2
    • Using a Phillips #1 screwdriver, remove the two 14 mm screws located closest to the center of the hoverboard.

    • Using a Phillips #1 screwdriver, remove the four 12 mm screws located in the middle of the panel.

    • Using a Phillips #1 screwdriver, remove two 15 mm screws located closest to the wheel.

  3. Hover-1 Titan Left Gyroscope Replacement: paso 3, imagen 1 de 3 Hover-1 Titan Left Gyroscope Replacement: paso 3, imagen 2 de 3 Hover-1 Titan Left Gyroscope Replacement: paso 3, imagen 3 de 3
    • Grip the bottom left panel and lift up to remove.

  4. Hover-1 Titan Left Gyroscope Replacement, Left Gyroscope and Motherboard: paso 4, imagen 1 de 2 Hover-1 Titan Left Gyroscope Replacement, Left Gyroscope and Motherboard: paso 4, imagen 2 de 2
    • Unplug the battery from the gyroscope by holding the yellow connector and pulling apart.

  5. Hover-1 Titan Left Gyroscope Replacement: paso 5, imagen 1 de 3 Hover-1 Titan Left Gyroscope Replacement: paso 5, imagen 2 de 3 Hover-1 Titan Left Gyroscope Replacement: paso 5, imagen 3 de 3
    • Remove four 12 mm Phillips #1 head screws from the corners of the green gyroscope/motherboard.

  6. Hover-1 Titan Left Gyroscope Replacement: paso 6, imagen 1 de 2 Hover-1 Titan Left Gyroscope Replacement: paso 6, imagen 2 de 2
    • Unplug the bottom right connector by squeezing it and pulling it away from the board.

  7. Hover-1 Titan Left Gyroscope Replacement: paso 7, imagen 1 de 2 Hover-1 Titan Left Gyroscope Replacement: paso 7, imagen 2 de 2
    • Unplug the light connector by squeezing it and pulling away from the board.

  8. Hover-1 Titan Left Gyroscope Replacement: paso 8, imagen 1 de 2 Hover-1 Titan Left Gyroscope Replacement: paso 8, imagen 2 de 2
    • Unplug the blue and white wires by squeezing the connector and pulling away from the board.

  9. Hover-1 Titan Left Gyroscope Replacement: paso 9, imagen 1 de 2 Hover-1 Titan Left Gyroscope Replacement: paso 9, imagen 2 de 2
    • Unplug the small white connector by squeezing it and pulling away from the board.

  10. Hover-1 Titan Left Gyroscope Replacement: paso 10, imagen 1 de 2 Hover-1 Titan Left Gyroscope Replacement: paso 10, imagen 2 de 2
    • Unplug the plug in the red connector.

    • The red plug is glued to the board, so this step will require extra force.

  11. Hover-1 Titan Left Gyroscope Replacement: paso 11, imagen 1 de 2 Hover-1 Titan Left Gyroscope Replacement: paso 11, imagen 2 de 2
    • Unplug the charging cable connector by squeezing it and pulling it away from the board.

  12. Hover-1 Titan Left Gyroscope Replacement: paso 12, imagen 1 de 1
    • Cut the cable tie.

    • Unplug the remaining wires.

    • The connectors for the remaining wires are in the rubber covers.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Jessica Ouyang

Miembro Desde 10/08/18

619 Reputación

4 Guías creadas

Equipo

Cal Poly, Team S15-G4, White Fall 2018 Miembro de Cal Poly, Team S15-G4, White Fall 2018

CPSU-WHITE-F18S15G4

4 Miembros

10 Guías creadas

2 comentarios

I’ve got an active broken on the cover not the one to to speaker the other one. Does anyone know where is terminates. I can’t see where it came from. It can only reach the circuit board or the active of the speaker.

Mark - Contestar

Where do you buy the board?

eden11 - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 3

Ultimos 30 días: 27

Todo El Tiempo: 972