Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Partes y herramientas

Introducción

If your hoverboard is experiencing issues where it will not move forward or unable to maintain balance, there is a problem with the gyroscope controlling the wheels.

  1. Flip the hoverboard over so the labels are facing upwards. Remove the twenty 18mm screws using a Phillips #2 screwdriver and twisting counterclockwise.
    • Flip the hoverboard over so the labels are facing upwards.

    • Remove the twenty 18mm screws using a Phillips #2 screwdriver and twisting counterclockwise.

  2. Remove the bottom cover by lifting it away from the hoverboard. The cover on the side without the battery has two wires connecting the power button and charging port.
    • Remove the bottom cover by lifting it away from the hoverboard.

    • The cover on the side without the battery has two wires connecting the power button and charging port.

  3. Remove one connector from the non-battery side circuit board. Remove the next connector from the non-battery side circuit board. To remove the connectors, pinch the plug and pull away from the circuit board.
    • Remove one connector from the non-battery side circuit board.

    • Remove the next connector from the non-battery side circuit board.

    • To remove the connectors, pinch the plug and pull away from the circuit board.

  4. Kits para Nintendo Switch

    Una solución rápida para volver al juego

    Comprar kits de Switch

    Kits para Nintendo Switch

    Una solución rápida para volver al juego

    Comprar kits de Switch
  5. Place the hoverboard so the sensor boards face you.
    • Place the hoverboard so the sensor boards face you.

  6. Remove battery connector by pulling it apart. Slide the rubber sheaths away from the connector on the blue, green, and yellow wires.
    • Remove battery connector by pulling it apart.

    • Slide the rubber sheaths away from the connector on the blue, green, and yellow wires.

    • Disconnect the colored wires by pulling them apart.

    • The large colored wires connecting the sensor boards to the wheels need to match for the motor to operate correctly.

  7. Remove the white cable from the sensor boards by disconnecting the cable on each side of the hoverboard. To release the cable connector, squeeze the sides while pulling it away from the sensor board.
    • Remove the white cable from the sensor boards by disconnecting the cable on each side of the hoverboard.

    • To release the cable connector, squeeze the sides while pulling it away from the sensor board.

  8. Remove the four 10mm screws with a  Phillips #1 screwdriver. Remove the four 10mm screws with a  Phillips #1 screwdriver.
    • Remove the four 10mm screws with a Phillips #1 screwdriver.

  9. Remove the sensor board by lifting it away from the hoverboard. Repeat steps 4-8 to remove the sensor board from the other side.
    • Remove the sensor board by lifting it away from the hoverboard.

    • Repeat steps 4-8 to remove the sensor board from the other side.

Conclusión

To reassemble your device, follow these instructions in reverse order.

5 personas más completaron esta guía.

Eduardo Miranda

Miembro Desde 08/10/18

298 Reputación

2 Guías creadas

Equipo

Cal Poly, Team S13-G2, White Fall 2018 Miembro de Cal Poly, Team S13-G2, White Fall 2018

CPSU-WHITE-F18S13G2

3 Miembros

4 Guías creadas

Where can you purchase the replacement board for the Hover-1 liberty?

Clifton Hale - Contestar

Where do you get replacement board?

Tim Sole - Contestar

After riding just a few times the hover board wouldn’t move. Also it has a rattle inside

Regina - Contestar

Make this site useful by telling us where we can buy a new circuit board.

tim stoinski - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 5

Ultimos 7 días: 21

Ultimos 30 días: 112

Todo El Tiempo: 2,607