Repara tus cosas Comunidad Tienda

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

Hover-1 H1 Charging Port Replacement

Introducción

Replacing the charging port of your Hover-1 H1 hoverboard will help to solve charging problems.

Qué necesitas

  1. Hover-1 H1 Charging Port Replacement, Bottom Shell: paso 1, imagen 1 de 1

    • Remove the ten 9mm machine screws by using a long Phillips #2 screwdriver to rotate the screws counterclockwise.

    • Remove the twelve 9mm sheet metal screws by using a long Phillips #2 screwdriver to rotate the screws counterclockwise.

    Traducir

  2. Hover-1 H1 Charging Port Replacement: paso 2, imagen 1 de 1

    • Puncture the two black stickers by using the tip of a screwdriver.

    • Remove the two 9mm machine screws by using a long Phillips #2 screwdriver to rotate the screws counterclockwise.

    Traducir

  3. Hover-1 H1 Charging Port Replacement: paso 3, imagen 1 de 2 Hover-1 H1 Charging Port Replacement: paso 3, imagen 2 de 2

    • Lift each side of the bottom shell by pulling up.

    • When lifting the shell, take care to not tear any cables from their connectors.

    Traducir

  5. Hover-1 H1 Charging Port Replacement: paso 4, imagen 1 de 1

    • Unplug the battery by pulling gently on both sides of the orange connector.

    Traducir

  6. Hover-1 H1 Charging Port Replacement, Charging Port: paso 5, imagen 1 de 2 Hover-1 H1 Charging Port Replacement, Charging Port: paso 5, imagen 2 de 2

    • Using a utility knife, scratch off the hot glue from the connector attaching the red and black wires to the motherboard.

    • Be careful to not damage the wires or connector when removing the glue.

    Traducir

  7. Hover-1 H1 Charging Port Replacement: paso 6, imagen 1 de 1

    • Remove the charging port connector from the motherboard by squeezing the connector and pulling the connector up.

    Traducir

  8. Hover-1 H1 Charging Port Replacement: paso 7, imagen 1 de 2 Hover-1 H1 Charging Port Replacement: paso 7, imagen 2 de 2

    • Using an adjustable wrench, unscrew the nut that is attaching the charging port to the bottom shell.

    • It might be helpful to put the charger in the charging port while unscrewing the nut to ensure that the port is not spinning.

    Traducir

  9. Hover-1 H1 Charging Port Replacement: paso 8, imagen 1 de 2 Hover-1 H1 Charging Port Replacement: paso 8, imagen 2 de 2

    • Pull the charging port to the left through the shell.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 1 otro colaborador

Madeline David

Miembro Desde 10/08/18

280 Reputación

2 Guías creadas

Insignias: 9

+ 6 más insignias

Equipo

Cal Poly, Team S17-G6, White Fall 2018 Miembro de Cal Poly, Team S17-G6, White Fall 2018

CPSU-WHITE-F18S17G6

4 Miembros

7 Guías creadas

Un comentario

I need to replace the charging port on my H1 hoverboard. Can you share the link for the actual replacement part.

prdrngga - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 6

Ultimos 30 días: 48

Todo El Tiempo: 3,851