Repara tus cosas Únete a la comunidad Tienda

Hasbro furby 2012 Light Sensor Replacement

Introducción

This guide will show you how to replace the Furby's light sensor circuit board.

Qué necesitas

  1. Hasbro furby 2012 Light Sensor Replacement, Outer Shell: paso 1, imagen 1 de 3 Hasbro furby 2012 Light Sensor Replacement, Outer Shell: paso 1, imagen 2 de 3 Hasbro furby 2012 Light Sensor Replacement, Outer Shell: paso 1, imagen 3 de 3

    • Use a flathead screwdriver to remove the two 10mm screws on the base of the Furby.

    Editar

  2. Hasbro furby 2012 Light Sensor Replacement: paso 2, imagen 1 de 3 Hasbro furby 2012 Light Sensor Replacement: paso 2, imagen 2 de 3 Hasbro furby 2012 Light Sensor Replacement: paso 2, imagen 3 de 3

    • Use a Phillips #0 driver to unscrew the eight 10mm screws.

    • Remove the base ring after unscrewing all the screws.

    • Be careful when lifting the base ring from the Furby. There are sharp edges that hold the base ring in place.

    Editar

  3. Hasbro furby 2012 Light Sensor Replacement: paso 3, imagen 1 de 2 Hasbro furby 2012 Light Sensor Replacement: paso 3, imagen 2 de 2

    • Unhook the white ribbon from the tab on the base.

    Editar

  4. Hasbro furby 2012 Light Sensor Replacement: paso 4, imagen 1 de 3 Hasbro furby 2012 Light Sensor Replacement: paso 4, imagen 2 de 3 Hasbro furby 2012 Light Sensor Replacement: paso 4, imagen 3 de 3

    • Roll the Furby's fur downward.

    • Disconnect the now exposed red wire.

    Editar

  5. Hasbro furby 2012 Light Sensor Replacement: paso 5, imagen 1 de 3 Hasbro furby 2012 Light Sensor Replacement: paso 5, imagen 2 de 3 Hasbro furby 2012 Light Sensor Replacement: paso 5, imagen 3 de 3

    • Locate the two middle clips first.

    • Locate the two remaining clips on Furby's sides, they are opposite each other.

    • Orient the Furby upside down with the tail facing away from you.

    Editar

  7. Hasbro furby 2012 Light Sensor Replacement: paso 6, imagen 1 de 3 Hasbro furby 2012 Light Sensor Replacement: paso 6, imagen 2 de 3 Hasbro furby 2012 Light Sensor Replacement: paso 6, imagen 3 de 3

    • Insert a metal prying tool directly into the clip opening.

    • Press upward into the clip. At the same time, use your other hand to pull away the plastic seam from the Furby's body.

    • Repeat the previous step to remove the remaining three clips.

    Editar

  8. Hasbro furby 2012 Light Sensor Replacement: paso 7, imagen 1 de 3 Hasbro furby 2012 Light Sensor Replacement: paso 7, imagen 2 de 3 Hasbro furby 2012 Light Sensor Replacement: paso 7, imagen 3 de 3

    • Locate the two 10mm screws and remove them with the Phillips #0 head screwdriver.

    • Lift up on the fur covering until the face of the Furby is exposed.

    Editar

  9. Hasbro furby 2012 Light Sensor Replacement: paso 8, imagen 1 de 3 Hasbro furby 2012 Light Sensor Replacement: paso 8, imagen 2 de 3 Hasbro furby 2012 Light Sensor Replacement: paso 8, imagen 3 de 3

    • Orient the Furby on its side to where the beak is facing left and locate the edge of the aluminum tape.

    • Lift tape gently and peel back until the tape is nearly removed.

    • Do not pull on the yellow wire located on the opposite end of the tape.

    Editar

  10. Hasbro furby 2012 Light Sensor Replacement: paso 9, imagen 1 de 2 Hasbro furby 2012 Light Sensor Replacement: paso 9, imagen 2 de 2

    • Locate the four 10mm screws. Two on either side of body, and two on top of back plate, around the tape.

    • Remove the 10mm screws with the Phillips#0 screwdriver.

    Editar

  11. Hasbro furby 2012 Light Sensor Replacement: paso 10, imagen 1 de 1

    • Peel the tape gently, grabbing it from the bottom edge and folding the tape upward.

    • Peel the tape up until it is nearly detached from the black case.

    Editar

  12. Hasbro furby 2012 Light Sensor Replacement: paso 11, imagen 1 de 2 Hasbro furby 2012 Light Sensor Replacement: paso 11, imagen 2 de 2

    • Orient the Furby face down, with the base facing away from you.

    • Locate the clips below the ears.

    • Repeat the technique used in Step 6. Create leverage using a metal prying tool to press upward into the clip, while also pulling back on the clip itself.

    Editar

  13. Hasbro furby 2012 Light Sensor Replacement: paso 12, imagen 1 de 2 Hasbro furby 2012 Light Sensor Replacement: paso 12, imagen 2 de 2

    • Remove the loose, plastic back panel by pulling the panel away from Furby's body.

    Editar

  14. Hasbro furby 2012 Light Sensor Replacement, Light Sensor: paso 13, imagen 1 de 3 Hasbro furby 2012 Light Sensor Replacement, Light Sensor: paso 13, imagen 2 de 3 Hasbro furby 2012 Light Sensor Replacement, Light Sensor: paso 13, imagen 3 de 3

    • Remove the 10mm Phillips #0 screw holding the circuit board in.

    • Gently lift out the circuit board.

    Editar

  15. Hasbro furby 2012 Light Sensor Replacement: paso 14, imagen 1 de 2 Hasbro furby 2012 Light Sensor Replacement: paso 14, imagen 2 de 2

    • Orient the Furby with the tail pointing left and the face pointing right.

    • Use the pointed tweezers to spread open the socket, and the blunt tweezers to grip and tug out the connector.

    • Insert your replacement light sensor connector.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 3 otros colaboradores

Jordan Castillo

Miembro Desde 10/06/16

785 Reputación

5 Guías creadas

Insignias: 15

+ 12 más insignias

Equipo

Cal Poly, Team 15-5, Livingston Fall 2016 Miembro de Cal Poly, Team 15-5, Livingston Fall 2016

CPSU-LIVINGSTON-F16S15G5

4 Miembros

6 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 2

Ultimos 30 días: 12

Todo El Tiempo: 1,035