Repara tus cosas Comunidad Tienda

Hamilton Beach 51101BA Motor Replacement

Introducción

After using this guide you will have learned how to replace the motor to your blender. You will need to use basic tools and soldering to complete this guide.

Qué necesitas

  1. Hamilton Beach 51101BA Motor Replacement, Rotor: paso 1, imagen 1 de 3 Hamilton Beach 51101BA Motor Replacement, Rotor: paso 1, imagen 2 de 3 Hamilton Beach 51101BA Motor Replacement, Rotor: paso 1, imagen 3 de 3

    • Remove the container from the blender.

    • Hold the blender and the container, then twist the container in a clockwise motion.

    • Make sure to follow the lock and unlock markings on the container.

    Editar

  2. Hamilton Beach 51101BA Motor Replacement: paso 2, imagen 1 de 1

    • Turn the blender so the bottom is facing you.

    • Using a Phillips #2 screwdriver, remove the two 5 mm Phillips screws from the base.

    Editar

  3. Hamilton Beach 51101BA Motor Replacement: paso 3, imagen 1 de 1

    • Using a Phillips #2 screwdriver, remove the two 5 mm Phillips screws from the motor platform.

    Editar

  5. Hamilton Beach 51101BA Motor Replacement: paso 4, imagen 1 de 1

    • Unhinge the plastic motor platform from the blender.

    • You may need a plastic spudger to unhinge the motor platform from the blender.

    Editar

  6. Hamilton Beach 51101BA Motor Replacement: paso 5, imagen 1 de 2 Hamilton Beach 51101BA Motor Replacement: paso 5, imagen 2 de 2

    • Using a spudger, carefully insert the tip into the coil of wire around motor.

    • This is used to hold the rotating piece of the motor still.

    Editar

  7. Hamilton Beach 51101BA Motor Replacement: paso 6, imagen 1 de 1

    • Remove the white rotor piece by rotating it counter-clockwise.

    • While rotating, make sure the rotating piece of the motor remains still.

    Editar

  8. Hamilton Beach 51101BA Motor Replacement, Motor: paso 7, imagen 1 de 2 Hamilton Beach 51101BA Motor Replacement, Motor: paso 7, imagen 2 de 2

    • Move the motor platform to the side.

    • Lift up the motor and remove it from the blender.

    Editar

  9. Hamilton Beach 51101BA Motor Replacement: paso 8, imagen 1 de 1

    • Some soldering experience required!

    • Desolder the red wire from the green plastic piece.

    Editar

  10. Hamilton Beach 51101BA Motor Replacement: paso 9, imagen 1 de 1

    • Cut the thin black wire from the wire cap.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 2 otros colaboradores

Andrew Huff

Miembro Desde 09/04/15

568 Reputación

3 Guías creadas

Insignias: 13

+ 10 más insignias

Equipo

USF Tampa, Team 2-5, Sullivan Fall 2015 Miembro de USF Tampa, Team 2-5, Sullivan Fall 2015

USFT-SULLIVAN-F15S2G5

4 Miembros

5 Guías creadas

2 comentarios

This article appears to be unfinished. You cut 2 wires at the end... then what? Reconnecting them doesn't make any sense.

Geo Jack Jack - Contestar

Que tipo de motor tengo que comprar?

hugoalex521 - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 19

Ultimos 30 días: 67

Todo El Tiempo: 6,794