Introducción
Utiliza esta guía para reemplazar los paneles del platillo del controlador HTC Vive. Deberás quitar estos paneles antes de poder acceder a cualquier otro componente del controlador. Retira los paneles superior e inferior del platillo con cuidado. Los clips de plástico que sujetan los paneles del platillo pueden romperse si se manipulan con demasiada brusquedad.
Qué necesitas
-
-
Voltea el controlador Vive para que el plato inferior quede hacia arriba.
-
Usa el destornillador Torx T5 para quitar los tres tornillos negros de 21 mm del plato inferior.
-
-
-
Usa la espátula de nailon para separar las cubiertas superior e inferior del plato alrededor de los bordes.
-
Retira solo la cubierta superior del platillo tirando hacia arriba con la mano.
My top saucer was REALLY stubborn. Don’t force it with your hand, use the spudger to separate it at the seam. Try not to poke your spudger in too deep, there are internals just inside the seam.
The second time around, I learned why it was so stubborn. The picture suggests that you should start at the base of the saucer and work your way around, but that’s backwards.
Start separating with your spudger at the distal side of the saucer and work your way toward the handle. Then for the last part, pull the piece up and away, like peeling a banana. See the second picture for the bottom half of the saucer, below. Do the same on the top.
-
-
-
-
Utiliza el destornillador Phillips 00 para quitar los tres tornillos plateados de 12,8 mm del panel del sensor superior expuesto.
It’s Phillips 0, not 00.
You do not need to remove these screws to remove the bottom saucer. They provide stability to the two halves of the donut.
I had the same experience. Putting the screws back in made the bottom shell easier to remove.
I concur, you don’t need to remove these screws to take the bottom shell off.
I found mine had ph#000 screws size, not ph#00.
please do not remove the Phillips-head screws it is not necessary to remove them.
-
-
-
Retira con cuidado la tapa del plato inferior con la mano.
From what I can tell, there are two clicks on each side? one is quite easy, then the other one seems to require considerable force pushing down and on the side, I had to do it one side at a time and found two YouTube videos performing this step to use as reference. I have the vive pro wands and not the originals, so this may explain the difference. This felt very wrong to me.
-
Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.
Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
6 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
¡ Francisco Javier Saiz Esteban nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
3 comentarios
Where do you get the replacement parts?
Vive dont less these parts we need to 3D print them its a Nightmare RN for business especially arcades
My controller only has 2 screws that are different sizes than a t5 and the 3rd is completely covered up by plastic. I have the sticky button problem, halp pls
Where can I buy new t5 21 mm screws? Mine are getting stripped out!
jeremyvanwoerden - Contestar
Where can you get replacement batteries?
Mike Justice - Contestar
The middle bottom screw may have some form of warranty sticker on it if you have a Vive Pro wand (which is purple). Mine had this. Easy enough to remove and get on with it.
sodiboo - Contestar