Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
-
Llena una olla o cacerola con suficiente agua para sumergir completamente el iOpener.
-
Calienta el agua hasta que hierva. Apaga el fuego.
-
Coloca un iOpener en el agua caliente durante 2-3 minutos. Asegúrate de que el iOpener esté completamente sumergido en el agua.
-
Utiliza unas pinzas para extraer el iOpener calentado del agua caliente.
-
Seca bien el iOpener con una toalla.
-
Tu iOpener está listo para ser utilizado. Si necesita recalentar el iOpener, calienta el agua hasta que hierva, apaga el fuego y coloca el iOpener en el agua durante 2-3 minutos.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Handling it by the tag, place the heated iOpener across the bottom casing.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently place an opening pick in the corner of the gap between the bottom casing and rear case.
-
Slide the opening pick along the side of the casing, prying it away from the adhesive as you go.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use your fingers to pull the bottom casing off the rest of the phone.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Starting at the groove near the headphone jack, use a plastic opening tool to lift the top casing.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use your fingers to pull the top casing off of the rest of the phone.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following screws holding the rear case to the rest of the phone:
-
Two 3.15 mm Phillips #00 screws
-
One 4.15 Torx T5 screw
-
One 4 mm Torx T5 screw
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Place your fingers on either side of the phone and gently push up on the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the rear case away from the rest of the phone with your hands.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the pointed end of a spudger, lift the battery cable and release the connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Switching to the flat end of the spudger, work your way underneath the battery and peel it away from the adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the three 3.15mm Phillips #00 screws from the turquoise case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a plastic opening tool, lift the turquoise case from the end near the headphone jack.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
A camera filter is now free to move, so remove it using tweezers.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use tweezers to lift the yellow polyimide tape that covers the ZIF connectors.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the pointed end of a spudger to lift the white tab on the largest ZIF connector opposite the USB connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the pointed edge of a spudger to work the ZIF cable out of its connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Repeat the procedure from steps 19 and 20 to remove the cables from the remaining ZIF connectors.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the pointed end of the spudger, pop the antenna cable from its connector on the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the 3.15 mm Phillips #00 screw from the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using tweezers, remove the adhesive tape around the headphone jack.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a soldering iron set at 400 degrees Celsius (752 degrees Fahrenheit), heat the solder joints lateral to the headphone jack. Use a pair of tweezers to lift the headphone jack from the board.
-