Repara tus cosas Comunidad Tienda

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

HTC Hero Trackball Replacement

Qué necesitas

  1. HTC Hero Trackball Replacement, Back Case: paso 1, imagen 1 de 1

    • Remove the back of the phone by pushing firmly with your thumbs up towards the camera.

    • Remove both the battery and the SD card (Press SD card in to release)

    • Locate and remove the four Torx screws highlighted in the photo, with the phone laying face down on your work space.

    Traducir

  2. HTC Hero Trackball Replacement: paso 2, imagen 1 de 1

    • Carefully pry the inside back cover from the device using an appropriate size plastic opening tool or small flathead screwdriver.

    • Insert the flat end between the back and front enclosure, working your way around the rim.

    Traducir

  3. HTC Hero Trackball Replacement: paso 3, imagen 1 de 1

    • Gently depress and release the small plastic tabs around the rim in the front enclosure, highlighted here.

    • It is best to start with the tab found on the top center of the phone, as it is easiest to locate.

    Traducir

  5. HTC Hero Trackball Replacement: paso 4, imagen 1 de 2 HTC Hero Trackball Replacement: paso 4, imagen 2 de 2

    • Carefully separate the front and back enclosures once all of the clips have been disengaged.

    • Be sure to not separate too quickly or you risk breaking an attached tab.

    Traducir

  6. HTC Hero Trackball Replacement, Trackball: paso 5, imagen 1 de 2 HTC Hero Trackball Replacement, Trackball: paso 5, imagen 2 de 2

    • Remove the two screws near the bottom of the motherboard with a Phillips head screwdriver.

    Traducir

  7. HTC Hero Trackball Replacement: paso 6, imagen 1 de 2 HTC Hero Trackball Replacement: paso 6, imagen 2 de 2

    • Gently pull off the ribbons holding the sides of the motherboard to the front enclosure.

    Traducir

  8. HTC Hero Trackball Replacement: paso 7, imagen 1 de 2 HTC Hero Trackball Replacement: paso 7, imagen 2 de 2

    • Remove the motherboard from within the front enclosure.

    • Be careful when pulling the ribbons off the motherboard as they may rip or break.

    Traducir

  9. HTC Hero Trackball Replacement: paso 8, imagen 1 de 2 HTC Hero Trackball Replacement: paso 8, imagen 2 de 2

    • Tilt the inside of the front enclosure towards your cupped palm to remove the trackball and it's enclosure will fall out.

    Traducir

  10. HTC Hero Trackball Replacement: paso 9, imagen 1 de 3 HTC Hero Trackball Replacement: paso 9, imagen 2 de 3 HTC Hero Trackball Replacement: paso 9, imagen 3 de 3

    • Position the phone off of the edge of the table and insert the replacement part by inserting the bevel then the trackball into the hole.

    • Make sure the two plastic pins on the trackball bevel are oriented horizontally.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Autor

con 4 otros colaboradores

Max Brown

Miembro Desde 01/23/12

139 Reputación

4 Guías creadas

Insignias: 7

+ 4 más insignias

Equipo

Cal Poly, Team 3-26, Amido Winter 2012 Miembro de Cal Poly, Team 3-26, Amido Winter 2012

CPSU-AMIDO-W12S3G26

5 Miembros

12 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 0

Todo El Tiempo: 1,510