Saltar al contenido principal

HP iPAQ h4155 button panel replacement

Qué necesitas

  1. HP iPAQ h4155 button panel replacement, Battery: paso 1, imagen 1 de 1
    • While sliding the silver release tab up, simultaneously lift the cover up from the left side.

  2. HP iPAQ h4155 button panel replacement: paso 2, imagen 1 de 1
    • Push the tab left to right to remove the cover.

  3. HP iPAQ h4155 button panel replacement: paso 3, imagen 1 de 1
    • Now, lift the battery up and away from the device to remove it.

  4. HP iPAQ h4155 button panel replacement, Back Case: paso 4, imagen 1 de 1
    • Remove the four silver screws using the T5 Torx Screwdriver (T5 x .25 in).

  5. HP iPAQ h4155 button panel replacement: paso 5, imagen 1 de 1
    • Remove the single black screw that is located beneath the HP sticker with the T5 Torx Screwdriver.

  6. HP iPAQ h4155 button panel replacement: paso 6, imagen 1 de 2 HP iPAQ h4155 button panel replacement: paso 6, imagen 2 de 2
    • Next, use your plastic removal tool to separate the gray back from the black center piece.

    • For better results, start the separation at the corner piece.

  7. HP iPAQ h4155 button panel replacement: paso 7, imagen 1 de 1
    • Remove the back case.

  8. HP iPAQ h4155 button panel replacement, Face Plate: paso 8, imagen 1 de 1
    • Now that the back cover is removed, use the #00 Philips x .17 screwdriver to remove the small screw to the left of the SD card slot.

  9. HP iPAQ h4155 button panel replacement: paso 9, imagen 1 de 2 HP iPAQ h4155 button panel replacement: paso 9, imagen 2 de 2
    • Next, unlock and remove the ribbon cable.

    • Using metal tweezers, carefully pull back on both sides of the brown bar unlocking the cable and slipping it out of the connector.

    • The bar, the connector, and the cable are fragile components that are easily broken.

  10. HP iPAQ h4155 button panel replacement: paso 10, imagen 1 de 2 HP iPAQ h4155 button panel replacement: paso 10, imagen 2 de 2
    • Next, remove the wire from the bottom of the mother board.

    • The easiest method is to use metal tweezers and grip the plug closest to the connector.

    • Make sure all the connections are properly disconnected before separation from the motherboard.

  11. HP iPAQ h4155 button panel replacement: paso 11, imagen 1 de 1
    • Next, use a plastic removal tool and separate the silver front case from the black frame.

  12. HP iPAQ h4155 button panel replacement, JoyPad buttons: paso 12, imagen 1 de 1
    • Remove the 4 screws along the bottom of the faceplate

    • They are #00 Philips head screws

  13. HP iPAQ h4155 button panel replacement: paso 13, imagen 1 de 2 HP iPAQ h4155 button panel replacement: paso 13, imagen 2 de 2
    • Once removed you can easily separate the keys from the body.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

John Pagliero

Miembro Desde 01/27/11

942 Reputación

7 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 2

Todo El Tiempo: 439