Menú

Tus configuraciones

Mi Mesa de Trabajo

Obtén acceso rápido a guías, partes y respuestas para tus dispositivos
Mi Carrito

Al parecer tu carrito está vacío

Visita Nuestra Tienda

HP iPAQ H2200 motherbaord replacement

Escrito Por: Tyler Andrews (y 8 de otros participantes)
  • Comentarios: 0
  • Favoritos: 3
  • Terminaciones: 3

Dificultad

Moderar

Pasos

11

Tiempo Requerido

15 minutos

Secciones

2

Banderas

0

Introducción

The purpose of this guide is to instruct the reader on how to remove the main board of their HP iPAQ H2200 device.

Herramientas

Comprar estas herramientas

Partes

No se requieren partes.

  1. Press and slide the battery cover tab to remove battery cover.

    • Press and slide the battery cover tab to remove battery cover.

    Traducir

  2. Pull on the black tab to lift the battery out of the battery compartment. Pull on the black tab to lift the battery out of the battery compartment.

    • Pull on the black tab to lift the battery out of the battery compartment.

    Traducir

  3. Remove the stylus by sliding it out of the slot.

    • Remove the stylus by sliding it out of the slot.

    Traducir

  4. Remove the CF card by sliding it out of the slot at the top of the device.

    • Remove the CF card by sliding it out of the slot at the top of the device.

    Traducir

  5. ¡Envío gratuito para todos los pedidos de más de USD100.00 o que contengan un Pro Tech Toolkit!

    Visita Nuestra Tienda

    ¿Alguna vez arreglaste algo? Eso es genial.

    Comparte tu historia de reparación con #SoyUnGenio

    Todos somos Genios

    Comparte tu historia de reparación con #SoyUnGenio

  6. Press down and push the black side strips toward the top of the device to remove them.

    • Press down and push the black side strips toward the top of the device to remove them.

    Traducir

  7. Using the T5 Torx screwdriver, remove all six screws on the back and all screws on each side of the device. Using the T5 Torx screwdriver, remove all six screws on the back and all screws on each side of the device. Using the T5 Torx screwdriver, remove all six screws on the back and all screws on each side of the device.

    • Using the T5 Torx screwdriver, remove all six screws on the back and all screws on each side of the device.

    Traducir

  8. Remove the back faceplate by pushing and loosening the 4 side slots (2 on each side). Remove the back faceplate by pushing and loosening the 4 side slots (2 on each side).

    • Remove the back faceplate by pushing and loosening the 4 side slots (2 on each side).

    Traducir

  9. Open the LCD connector, where the orange strip attaches to the main board.

    • Open the LCD connector, where the orange strip attaches to the main board.

    Traducir

  10. Carefully remove the orange LCD strip from the connector.

    • Carefully remove the orange LCD strip from the connector.

    Traducir

  11. Unscrew the 2 screws located at each top corner of the main board.

    • Unscrew the 2 screws located at each top corner of the main board.

    Traducir

  12. Remove the main board by pushing outward on the two tabs located on each side near the bottom of the device.

    • Remove the main board by pushing outward on the two tabs located on each side near the bottom of the device.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

3 personas más completaron esta guía.

Autor

con 8 otros colaboradores

Tyler Andrews

Miembro Desde 13/01/10

191 Reputación

5 Guías creadas

Insignias: 6

+ 3 más insignias

Equipo

Cal Poly, Team 4-12, Forte Winter 2010 Miembro de Cal Poly, Team 4-12, Forte Winter 2010

CPSU-FORTE-W10S4G12

3 Miembros

5 Guías creadas

0 Comentarios

Agregar un comentario
Ver Estadísticas:

Ultimas 24 Horas: 1

Últimos 7 Días: 2

Últimos 30 Días: 4

Todo El Tiempo: 4,305