Saltar al contenido principal

Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.

Qué necesitas

  1. Este paso está sin traducir. Ayuda a traducirlo

    : paso 1, imagen 1 de 1
    • Turn off your laptop.

    • Ensure your laptop is off. Removing the battery while it is on may harm your laptop or yourself.

    • Flip over to view the bottom of the laptop in order to gain access the battery and the DVD±RW Drive.

  2. Este paso está sin traducir. Ayuda a traducirlo

    : paso 2, imagen 1 de 1
    • There are two battery release switches circled.

  3. Este paso está sin traducir. Ayuda a traducirlo

    : paso 3, imagen 1 de 1
    • slide release switches inward towards each other to release battery.

  4. Este paso está sin traducir. Ayuda a traducirlo

    : paso 4, imagen 1 de 1
    • after sliding the release switches, pull battery towards yourself to remove battery.

  5. Este paso está sin traducir. Ayuda a traducirlo

    : paso 5, imagen 1 de 2 : paso 5, imagen 2 de 2
    • There is one screw holding the DVD±RW Drive in place. Use the #00 screwdriver to remove the screw.

  6. Este paso está sin traducir. Ayuda a traducirlo

    : paso 6, imagen 1 de 3 : paso 6, imagen 2 de 3 : paso 6, imagen 3 de 3
    • The DVD±RW Drive is here. Remove by gently pulling it straight out.

    • After removal of the DVD±RW Drive, two screws are exposed and must be removed.

  7. Este paso está sin traducir. Ayuda a traducirlo

    : paso 7, imagen 1 de 2 : paso 7, imagen 2 de 2
    • Using your Phillips #00 screwdriver, remove the two screws to loosen the fittings of the keyboard.

    • One of the screws lies in the label.

  8. Este paso está sin traducir. Ayuda a traducirlo

    : paso 8, imagen 1 de 3 : paso 8, imagen 2 de 3 : paso 8, imagen 3 de 3
    • Flip the laptop over to view the top and lift the screen up.

    • There are sixteen clips holding the keyboard in place. Gently pry up each clip using a plastic opening tool. Once all clips are loose, lift the keyboard from the computer.

    • Do NOT pull the keyboard up more than 2-3 inches as there is a film-material connecting the keyboard to the laptop.

  9. Este paso está sin traducir. Ayuda a traducirlo

    : paso 9, imagen 1 de 3 : paso 9, imagen 2 de 3 : paso 9, imagen 3 de 3
    • There is a small black latch holding the film-material in place.

    • Flip the black latch up to release the film-material. Once flipped up, simply pull the film-material out from the laptop to release the keyboard.

    • There are tiny prongs on the ribbon; it must be carefully removed and upon re-installation the prongs must be lined up exactly in each tiny track in order for the keyboard to work.

    I used this guide to upgrade the memory on an HP 15-r011dx, and found that the keyboard ribbon is very finicky. In fact, the first time I put the PC back together, many of the keys on the keyboard didn’t work! Two more tries did the trick. I finally realized that the teeny, tiny teeth on the ribbon must be carefully threaded into the connector (i.e., lined up exactly in each tiny track) in order for the keyboard to work. I usually work on Macs and have never encountered this issue before now, but next time I take apart this, or any other PC laptop, I’ll know this is a quirk.

    Traveled Woman - Contestar

  10. Este paso está sin traducir. Ayuda a traducirlo

    : paso 10, imagen 1 de 1
    • Flip the laptop over to view the bottom and remove the remaining screws from the bottom.

    • There are 2 screws located underneath the covers.

  11. Este paso está sin traducir. Ayuda a traducirlo

    : paso 11, imagen 1 de 2 : paso 11, imagen 2 de 2
    • Flip your laptop over to view top and open it.

    • Remove the four screws and the two wires before removing the base of the laptop.

    • The metal prongs that wires fit onto stay attached to the computer and can be easily bent when trying to remove or place the plastic piece on to secure the wire. Also pay attention to how the plastic piece looks when you take them off (i.e. which side is up and facing out).

    The 2 DVD screws are on the underside of the laptop (you need to turn it over) - Not visible where the keyboard was.

    marcsimmons - Contestar

    It would be nice if you added how to unplug and plug back in the wires. I used two small flat head screwdrivers on each side of the white ‘plugs’ to gently apply equal pressure to remove them. However, since the wire is not attached to the white plug, which is not mentioned, and the white plug is quite small, it is difficult to figure out how to reassemble it, or which side of the plug was front/back, up/down. It looks like the wire strip lays on top of the wire teeth/posts that stick out and then you slide the plug on top of that to secure it. So far, no luck with this attempt.

    Patrick - Contestar

    After struggling to attach the two wires that had been unplugged, I would suggest using the blue plastic tabs that are attached to the wire to unplug them, instead of doing what I did above, which is pulling out the white plastic piece that holds the wires down. I have not tried it, and you might need to still remove the white plastic pieces that secure the wires, but it’s worth a shot. If you do end up removing the white plastic pieces, be warned that the metal prongs that they fit into and stay attached to the computer, can be easily bent when trying to place the plastic piece on to secure the wire, so if you are having a problem, check that. Also, pay attention to how the plastic piece looks when you take them off- which side is up and facing out.

    Patrick - Contestar

    The white retainer is designed to just flip up off the ribbon cable. No need to completely remove them. Gently pry up on the ribbon side of the white retainer to flip it up off the ribbon cable. Then the ribbon cable will slide out . Make sure , when reconnecting , the ribbon is fully seated, then flip the retainer down to secure.

    Mike Miller - Contestar

  12. Este paso está sin traducir. Ayuda a traducirlo

    : paso 12, imagen 1 de 1
    • Use your plastic opening tool to pry the base of the laptop off.

  13. Este paso está sin traducir. Ayuda a traducirlo

    : paso 13, imagen 1 de 3 : paso 13, imagen 2 de 3 : paso 13, imagen 3 de 3
    • There are two screws holding the hard drive in place. Remove these screws.

    • Remove the hard drive by pulling it to the right like shown.

  14. Este paso está sin traducir. Ayuda a traducirlo

    : paso 14, imagen 1 de 3 : paso 14, imagen 2 de 3 : paso 14, imagen 3 de 3
    • There are 3 screws holding the motherboard in place.

    • Unscrew the screws to release the motherboard.

  15. Este paso está sin traducir. Ayuda a traducirlo

    : paso 15, imagen 1 de 3 : paso 15, imagen 2 de 3 : paso 15, imagen 3 de 3
    • There are several wires that need to be disconnected from the motherboard.

    • Remove the wires carefully.

  16. Este paso está sin traducir. Ayuda a traducirlo

    : paso 16, imagen 1 de 1
    • After removing all the wires, pull the motherboard out.

Linea de Meta

4 personas más completaron esta guía.

Equipo

USF Tampa, Team 16-4, Watkins Winter 2015 Miembro de USF Tampa, Team 16-4, Watkins Winter 2015

USFT-WATKINS-W15S16G4

4 Miembros

6 Guías creadas

Un comentario

I need to buy this motherboard online

How can i find it?

Ahmed Mohsen Brary - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 1

Ultimos 30 días: 4

Todo El Tiempo: 3,885