Repara tus cosas Comunidad Tienda

HP Split x2 Screen Replacement

Introducción

Did you accidentally drop your device and shatter the screen? This guide will instruct you how to replace your broken screen. The first five steps tell you how to remove the rear cover of the case. The remaining six steps explain how to replace the screen.

Qué necesitas

  1. HP Split x2 Screen Replacement, Rear Cover: paso 1, imagen 1 de 1

    • Opening the device voids the manufacturer warranty.

    • Power down the HP Split x2 before beginning the repair

    • Separate the tablet from the keyboard by pushing the slider to the left and lifting the tablet from the keyboard.

    Traducir

  2. HP Split x2 Screen Replacement: paso 2, imagen 1 de 3 HP Split x2 Screen Replacement: paso 2, imagen 2 de 3 HP Split x2 Screen Replacement: paso 2, imagen 3 de 3

    • Remove the four white caps on the bottom edge of the tablet.

    • Use a tweezer to grasp white caps.

    • The white caps are easily lost. Store them in a secure place.

    Traducir

  3. HP Split x2 Screen Replacement: paso 3, imagen 1 de 1

    • Use a Phillips #000 screwdriver to remove the four 3mm screws.

    Traducir

  4. HP Split x2 Screen Replacement: paso 4, imagen 1 de 2 HP Split x2 Screen Replacement: paso 4, imagen 2 de 2

    • Use a plastic opening tool to pry the tabs on the top, left and right sides of the tablet.

    • Only the top and sides have tabs. Remove all tabs before lifting screen.

    Traducir

  6. HP Split x2 Screen Replacement: paso 5, imagen 1 de 2 HP Split x2 Screen Replacement: paso 5, imagen 2 de 2

    • Separate the cover and the screen.

    • Gently lift the screen out of the cover.

    Traducir

  7. HP Split x2 Screen Replacement, Screen: paso 6, imagen 1 de 2 HP Split x2 Screen Replacement, Screen: paso 6, imagen 2 de 2

    • Use a J0 screwdriver to remove the ten 4mm Phillips screws.

    Traducir

  8. HP Split x2 Screen Replacement: paso 7, imagen 1 de 2 HP Split x2 Screen Replacement: paso 7, imagen 2 de 2

    • Peel back the large black tape.

    • Remove the 4mm Phillips screw.

    Traducir

  9. HP Split x2 Screen Replacement: paso 8, imagen 1 de 3 HP Split x2 Screen Replacement: paso 8, imagen 2 de 3 HP Split x2 Screen Replacement: paso 8, imagen 3 de 3

    • Remove three 2 mm zero insertion force (ZIF) connectors. Lift the black tab in front and then remove the ribbon from the rear.

    • Remove two larger zero insertion force (ZIF) connectors. Lift the black tab in front and then remove the ribbon from the rear.

    Traducir

  10. HP Split x2 Screen Replacement: paso 9, imagen 1 de 3 HP Split x2 Screen Replacement: paso 9, imagen 2 de 3 HP Split x2 Screen Replacement: paso 9, imagen 3 de 3

    • The last attachment to the screen is the bronze colored display cable connector.

    • Use a pair of tweezers to lift the metal bar and swing it to the other side on top of the cable.

    • Pull in the direction of the cable to remove the connector.

    Traducir

  11. HP Split x2 Screen Replacement: paso 10, imagen 1 de 1

    • Glue is holding the device together along the edges. The glue is can be very strong. A heat gun may be required to loosen the glue for removal of the digitizer to prevent damage to the screen.

    • Apply pressure to to the sides of the tablet.

    • Separate the digitizer from the the body of the tablet.

    Traducir

    Glue was not very weak for me. I broke my screen trying to remove the digitizer. Recommend using a heat gun to weaken glue that is used to hold digitizer in place.

    rogershomework - Contestar

  12. HP Split x2 Screen Replacement: paso 11, imagen 1 de 2 HP Split x2 Screen Replacement: paso 11, imagen 2 de 2

    • Glue is holding the screen on at the four corners.

    • Lift the screen up, breaking any adhesion forced by the glue.

    • Replace the old screen with a new one.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

11 personas más completaron esta guía.

Autor

con 7 otros colaboradores

Ricky Huitema

Miembro Desde 09/24/15

449 Reputación

2 Guías creadas

Insignias: 9

+ 6 más insignias

Equipo

Texas Tech, Team 22-5, Rauch Fall 2015 Miembro de Texas Tech, Team 22-5, Rauch Fall 2015

TTU-RAUCH-F15S22G5

3 Miembros

2 Guías creadas

5 comentarios

This is not helpful because the one I am working on has no screws.

Matt Brown - Contestar

I also have a Split x2 with no screws

dbmacaulay -

I want change my screen because My screen is broken but I do not know , where I can buy my screen

Nohora Chitiva - Contestar

ebay or amazon

Andrei Isari -

Is HP Touch Screen Digitizer Glass for HP Split X2 The same as the screen being replaced here?? I need to know

Nwatu Chineme Edger - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 3

Ultimos 7 días: 11

Ultimos 30 días: 31

Todo El Tiempo: 13,107