Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
Rota la impresora 90 grados a la derecha, para que el lado de panel correspondiente al panel de control esté frente a ti.
-
Remueve los dos tornillos Torx T10 de 12 mm del panel izquierdo.
-
-
-
Aparta el panel superior de la impresora.
-
Remueve los dos tornillos Torx T10 de 12 mm del frente superior de la impresora.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Set aside the ink cartridge carriage.
-
Remove the three T10 12mm Torx screws holding the paper guide to the printer body.
-
Lift the paper guide directly up to remove it and set it aside.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the five T10 12mm Torx screws from the roller holder.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the plastic gear cover by pulling it away from the printer body and lifting it up.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the metal tab by rotating it away from the body of the printer and pulling up.
-
Remove the brush by grasping it firmly by the base and lift straight up.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the connector holding the feed roller motor to the logic board by pulling it strait up
-
Remove the T10 12mm Torx screw on the roller panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the page sensor from the logic board by pulling straight up on the connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Rotate the printer 180 degrees and turn it up on to the front side, so that the back of the printer is facing up and the bottom facing you.
-
Push in the tab on the left side of the back panel and pull outward to remove the back panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Tilt the printer up until the bottom of the printer can be seen.
-
Remove the T10 12mm Torx screw from the bottom panel.
-
Grasp the top edge of the bottom panel and pull to remove it.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the black plastic cross member from the bottom of the printer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the printer back down so that it is sitting on the bottom panel and rotate the printer 180 degrees.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the printer head cleaner by lifting the front of the printer head cleaner above the track and slide it forward.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the left side of the feed roller assembly and pull towards the front of the printer and up to free the metal tab from the slot.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the feed roller assembly straight up to remove it.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Set aside the printer base.
-
Flip the feed roller assembly over so that its bottom and so that the feed roller is on the left side.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the T10 12mm screw holding the feed roller in place.
-
Carefully pull apart the two plastic beams to free the feed roller and lift the feed roller out of the assemblage.
-
Cancelar: No complete esta guía.
8 personas más completaron esta guía.
Un comentario
Does the encoder wheel gear have to be exactly in a certain position, or does it not matter?