Saltar al contenido principal

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement

Qué necesitas

  1. HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement, Remove Back Panel: paso 1, imagen 1 de 1
    • Remove the back panel by inserting your fingers into the indentations next to the tabs. Press the tabs inward towards each other while pulling the back panel toward you.

  2. HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement, Remove Inner Back Pannel: paso 2, imagen 1 de 2 HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement, Remove Inner Back Pannel: paso 2, imagen 2 de 2
    • Using the T10 Torx Security Bit Screwdriver, unscrew the screws on the upper left and right corners of the inner panel to remove the inner back panel.

  3. HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement, Remove Upper Portion: paso 3, imagen 1 de 2 HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement, Remove Upper Portion: paso 3, imagen 2 de 2
    • Press down on the two plastic hinges to remove the upper portion of printer.

  4. HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement, Unplug Speaker Wire: paso 4, imagen 1 de 1
    • Grasp the plastic plug on the end of the speaker wire, then gently pull the plug away from the printer until the wire is removed.

  5. HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement, Removing Scanner Tray: paso 5, imagen 1 de 2 HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement, Removing Scanner Tray: paso 5, imagen 2 de 2
    • Rotate the printer so the paper tray is facing towards you.

    • Gently lift the scanner tray up and away from the printer.

    • Press the gray plastic tabs inward to release the tabs from the printer.

  6. HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement, Removing Scanner Tray - cont.: paso 6, imagen 1 de 1
    • Returning to the back of the printer, remove the scanner from the back hinges.

    • With pressure applied, the scanner will detach easily.

  7. HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement: paso 7, imagen 1 de 1
    • Gently grasp and unplug the two white ribbon cables from the printer body.

    • Be sure to grasp the cable at the connector and not to pull on the wires themselves.

  8. HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement: paso 8, imagen 1 de 1
    • Unplug the white plastic multi-wire connector (with orange, black, red, and brown wires) from it's port.

    • Be sure to grasp the white connector and not to pull on the wires themselves.

  9. HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement, Detaching the Scanner Tray: paso 9, imagen 1 de 1
    • Detach the scanner tray from the printer by lifting the scanner tray off the printer body.

  10. HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement, Printer Carriage: paso 10, imagen 1 de 1
    • Remove printer carriage cover by unscrewing 4 black coarse thread T-10 torx screws marked with red circles.

  11. HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement: paso 11, imagen 1 de 1
    • Depress the plastic tabs marked in yellow to release the cover from the sides.

  12. HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement: paso 12, imagen 1 de 3 HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement: paso 12, imagen 2 de 3 HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement: paso 12, imagen 3 de 3
    • Slide the printer carriage to the center of the printer. Disconnect the printer carriage from the rod one side at a a time by pulling upward.

    • Unhooking the printer carriage is difficult and will require a fair amount of force.

    • The plastic strip that guides the carriage is fragile and can be broken easily.

    • Pull carriage up from the bottom.

  13. HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement: paso 13, imagen 1 de 2 HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement: paso 13, imagen 2 de 2
    • Pull on the two white wire strips on the printer carriage to remove.

    • Wire strips are fragile. Pull from connection to carriage and not the ribbon cable itself.

  14. HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement: paso 14, imagen 1 de 3 HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement: paso 14, imagen 2 de 3 HP PSC 2410 Photosmart All In One Printer Printer Carriage Replacement: paso 14, imagen 3 de 3
    • Place new printer carriage on the carriage rod one side at a time.

    • For proper reassembly, place the printer carriage’s black lip beneath the overhanging metal flap at the back of the printer.

Conclusión

To reassemble your device, follow these instructions in reverse order.

4 personas más completaron esta guía.

Cody Long

Miembro Desde 04/12/11

153 Reputación

3 Guías creadas

Equipo

Cal Poly, Team 12-31, Maness Spring 2011 Miembro de Cal Poly, Team 12-31, Maness Spring 2011

CPSU-MANESS-S11S12G31

5 Miembros

9 Guías creadas

Un comentario

It would be a good idea to unhook the guide film whilst changing the carriage, then feeding it carefully through the IR head on the carriage PCB & re hooking it.

Rab - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 8

Ultimos 30 días: 41

Todo El Tiempo: 10,855