Introducción
Necesites acceder a los componentes internos de tu HP ELitebook 840 G5 para reparaciones más profundas, o solo estas buscando reemplazar la placa trasera de tu laptop debido a daño, por favor sigue la guía paso-a-paso de abajo para remover la cubierta trasera de tu HP Elitebook 849 G5 con seguridad. Para el reensamble, sigue las direcciones en pasos inversos. El proceso es requerido para varias reparaciones o reemplazos en este producto empiezan con este proceso vital de remover la cubierta trasera de la HP Elitebook 840. Asegúrate de ser precavido cuando completes esta reparación; ¡los componentes eléctricos internos de la laptop serán expuestos.!
Qué necesitas
-
-
Usa un desarmador Phillips # 1 para desatornillar los cinco tornillos. Los tres tornillos superiores son de 10 mm y los dos en los lados son de 7 mm.
-
Desatornilla los tres tornillos del inferior usando el mismo desarmador.
-
-
-
-
Voltea la computadora para que el lado donde este la bisagra este mirándote.
-
Usa la herramienta de apertura de plástico para hacer palanca y abrir la cubierta trasera.
-
Arrastra la herramienta de apertura de plástico a lo largo del borde de izquierda a derecha y usa una segunda herramienta de apertura para hacer palanca y abrir la esquina superior derecha.
-
Repite el tercer paso para el otro lado.
-
Repite en los lados Izquierdo y Derechos del sistema. Hay dos puntos en el centro (en los lados izquierdo y derecho del tornillo central) que se liberaran con un poco de ´presión ligera.
-
Para reensamblar tu dispositivo, sigue estas instrucciones en orden inverso. Este paso es critico, ya que es el inicio de todas las guías para acceder al interior de la computadora.
Para reensamblar tu dispositivo, sigue estas instrucciones en orden inverso. Este paso es critico, ya que es el inicio de todas las guías para acceder al interior de la computadora.
Cancelar: No complete esta guía.
6 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
¡ Fernando Salazar Garcia nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
2 comentarios
Thank you so much for this tutorial! I was able to remove my bloated battery and replace it without taking the notebook into a repair shop. I ordered the screwdrivers on Amazon and my new battery and the screwdrivers arrived today. Job done! :)
On my HP EliteBook 840 G5, the “two side screws” (black) are found inside the two holes seen next to the left top screw, and between the center and right top screw.
Ruedi Port - Contestar
Mine had the same, and these black screws also need to be released in order to remove the bottom panel.
Josh -
Correct. Some other models have 2 black screws at the back, near the corners.
The models with the 2 black screws, are missing the 2 silver screws at the left side and the right side in the middle.
Note: You need to release the 2 black screws as well, if your type of model has them.
koppie007 - Contestar
Thank you this was very helpful. I was able to remove the cover and the SSD.
Stupid question but is this board considered the hard drive? my laptop failed (no power) and I did get an identical replacement. In the past I have been able to remove the hard drive in the failed laptop and connect it to the new one via a data transfer cable (removed hard drive to usb in new laptop. I could then browse files off of the old hard drive and transfer them over to the new. This SSD board has vastly different connectors. Do you know if they make a transfer cable that connects to this board with a usb on the other end?
dgtuk1 - Contestar
I removed the back cover and installed a new SSD. When I went to put the back cover, the center screw would not go back in. It turns but does not catch. Any advice?
Erik - Contestar