Saltar al contenido principal

Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.

Qué necesitas

  1. Este paso está sin traducir. Ayuda a traducirlo

    : paso 1, imagen 1 de 1
    • Turn off your computer! Taking out the battery while it's still on is dangerous!

    • Flip the laptop over to the back.

    • Using two hands, push on the tabs while gently taking out the battery.

  2. Este paso está sin traducir. Ayuda a traducirlo

    : paso 2, imagen 1 de 3 : paso 2, imagen 2 de 3 : paso 2, imagen 3 de 3
    • Turn off computer before starting.

    • Flip to the backside of the laptop.

    • Using a Phillips #1 screwdriver, unscrew the 5mm screw and take off the shown cover.

    • Using the same screwdriver, unscrew the 8mm screws.

    • The screws may not completely fall out of the laptop, just ensure they are unscrewed as far as they will go.

  3. Este paso está sin traducir. Ayuda a traducirlo

    : paso 3, imagen 1 de 1
    • Flip over the laptop to the top side, and open the laptop.

    • Slide the locking tabs down using a blue plastic opening tool or your fingernail.

  4. Este paso está sin traducir. Ayuda a traducirlo

    : paso 4, imagen 1 de 2 : paso 4, imagen 2 de 2
    • Using the plastic prying tool, lift the keyboard gently towards you.

    • Don't take the keyboard completely off because it is still attached with a ribbon cable to the computer.

  5. Este paso está sin traducir. Ayuda a traducirlo

    : paso 5, imagen 1 de 1
    • Pull up on both sides of the black locking tab of the connector.

    • The keyboard should now be free of the computer.

  6. Este paso está sin traducir. Ayuda a traducirlo

    : paso 6, imagen 1 de 1
    • Put a finger under each side of the plastic lock on the ribbon cable and pull up.

    Reben pack Tut Gaya hai

    Gopal Ji - Contestar

    Reben cabal tuta huahai

    Gopal Ji - Contestar

  7. Este paso está sin traducir. Ayuda a traducirlo

    : paso 7, imagen 1 de 3 : paso 7, imagen 2 de 3 : paso 7, imagen 3 de 3
    • Using a flathead screwdriver, get under each plastic hinge cover until they pop.

    • Lift the right edge of plastic strip covering the power button and gently pull it up until the whole strip comes free.

  8. Este paso está sin traducir. Ayuda a traducirlo

    : paso 8, imagen 1 de 1
    • Using a flathead screwdriver, work both sides of the connector next to the fan and take it out.

  9. Este paso está sin traducir. Ayuda a traducirlo

    : paso 9, imagen 1 de 1
    • Using the T9 Torx screwdriver, remove one 7mm screw on the left hinge.

    • We recommend replacing this screw shortly after removing the cable as it helps hold the hinge to the lower half of the laptop.

  10. Este paso está sin traducir. Ayuda a traducirlo

    : paso 10, imagen 1 de 1
    • Using the blue plastic opening tool, pull the rubber covers off the screen screws.

  11. Este paso está sin traducir. Ayuda a traducirlo

    : paso 11, imagen 1 de 1
    • Using a T9 Torx screwdriver, remove the top four 5 mm screws.

    • Remove the bottom two 6 mm screws with the same screwdriver.

  12. Este paso está sin traducir. Ayuda a traducirlo

    : paso 12, imagen 1 de 3 : paso 12, imagen 2 de 3 : paso 12, imagen 3 de 3
    • Using a flat head screwdriver, pry the plastic panel over the screen up starting at one of the hinges.

    • Using the flathead, continue running the it under the the plastic screen edge and gently pry it off.

    • If you press the screwdriver tip down (by lifting the handle), the screen panel pops off easier.

  13. Este paso está sin traducir. Ayuda a traducirlo

    : paso 13, imagen 1 de 3 : paso 13, imagen 2 de 3 : paso 13, imagen 3 de 3
    • Slowly pry back the of the screen.

    • It is easiest to work both sides free at the same time.

  14. Este paso está sin traducir. Ayuda a traducirlo

    : paso 14, imagen 1 de 1
    • Using your fingers, take out the two connections near the hinges.

  15. Este paso está sin traducir. Ayuda a traducirlo

    : paso 15, imagen 1 de 1
    • Using the T9 Torx screwdriver, unscrew the four 4mm screws.

  16. Este paso está sin traducir. Ayuda a traducirlo

    : paso 16, imagen 1 de 2 : paso 16, imagen 2 de 2
    • Tilt the screen up from the top to gain access to the screws on the side.

    • Go just far enough to get to the bottom screws to avoid damaging the bracket.

    • Using the PH00 screwdriver, unscrew the 2.5mm screws on the side of the screen. There should be 4 on each side.

    • You can now take out the screen.

Linea de Meta

8 personas más completaron esta guía.

Khulan Orgil

Miembro Desde 04/14/15

1,135 Reputación

6 Guías creadas

Equipo

Cal Poly, Team 4-2, Maness Spring 2015 Miembro de Cal Poly, Team 4-2, Maness Spring 2015

CPSU-MANESS-S15S4G2

4 Miembros

6 Guías creadas

Un comentario

thank you I found it very interesting

Hassan - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 4

Ultimos 30 días: 15

Todo El Tiempo: 5,382