Saltar al contenido principal

Reemplazo de batería Google Pixel 4a

Qué necesitas

  1. Reemplazo de batería Google Pixel 4a, Expulsar la bandeja de la tarjeta SIM: paso 1, imagen 1 de 3 Reemplazo de batería Google Pixel 4a, Expulsar la bandeja de la tarjeta SIM: paso 1, imagen 2 de 3 Reemplazo de batería Google Pixel 4a, Expulsar la bandeja de la tarjeta SIM: paso 1, imagen 3 de 3
    • Introduce una herramienta de expulsión de SIM, una broca o un clip enderezado en el orificio de la bandeja SIM.

    • Presiona directamente en el orificio para expulsar la bandeja de la tarjeta SIM.

    • Retira la bandeja de la tarjeta SIM.

  2. Reemplazo de batería Google Pixel 4a, Notas de precaución: paso 2, imagen 1 de 3 Reemplazo de batería Google Pixel 4a, Notas de precaución: paso 2, imagen 2 de 3 Reemplazo de batería Google Pixel 4a, Notas de precaución: paso 2, imagen 3 de 3
    • Necesitarás separar la pantalla para separarla del teléfono. Lee las siguientes notas con cuidado antes de proceder.

    • Fíjate en las dos juntas en el borde del teléfono:

    • Junta de la pantalla: Esta junta separa la pantalla del resto del teléfono. Por aquí es por dónde debes separar.

    • Junta del marco: Aquí es donde el marco se encuentra con la carcasa trasera. Está enganchada por tornillos. No separes por esta junta.

    • Antes de comenzar, fíjate en las siguientes áreas de la pantalla.

    • Cable flexible de la pantalla: No insertes la púa de separación más allá de lo indicado o corres el riesgo de dañar este cable.

    • Ten cuidado con el cable plano naranja que está bajo la esquina inferior derecha de la pantalla, ya que puedes dañarlo si presionas tu púa sobre él. Introduce la púa solo lo necesario para separar el adhesivo de la pantalla.

    • Perímetro adhesivo: Separar más allá de este estrecho perímetro sin poner la púa en ángulo dañará el panel OLED.

    Coll down guys and gals.

    1) go below the Display and not between the backcover/middle (see the other comments)

    2) just take care about the flex/display cable position (which is iirc about on the middle i.e. 2nd 3rd from the bottom ON THE LEFT side dear OP)

    Everything else is just separting the glued on Display from the Phone.

    See the other comments

    Aleksandar Dejanovic - Contestar

    Cool down guys and gals.

    1) go below the Display and not between the backcover/middle (see the other comments)

    2) just take care about the flex/display cable position (which is iirc about on the middle i.e. 2nd 3rd from the bottom ON THE LEFT side dear OP)

    Everything else is just separting the glued on Display from the Phone.

    See the other comments

    Aleksandar Dejanovic - Contestar

    I've measured it: The cable starts arround 1.4-1.6 cm from the lower half from the bottom on the left side.

    So You can cut the bottom left corner and of course the upper left one but for safety's sake, watch out for the camera.

    You can go up to 5cm down from the upper left side till You're near the cable.

    Aleksandar Dejanovic - Contestar

    When you say left side, is this your left when the phone screen is facing you?

    jaunie -

    The third image her shows the back of the screen, not the body of the phone

    blueslondon - Contestar

  3. Reemplazo de batería Google Pixel 4a, Calienta el borde derecho de la pantalla: paso 3, imagen 1 de 1
    • Aplique un iOpener caliente en el borde derecho de la pantalla durante un minuto para ablandar el adhesivo.

    • También se puede utilizar un secador de pelo, una pistola de calor o una placa caliente, pero ten cuidado de no sobrecalentar el teléfono, ya que tanto la pantalla como la batería son susceptibles de sufrir daños debido al calor.

  4. Reemplazo de batería Google Pixel 4a, Insertar una púa: paso 4, imagen 1 de 3 Reemplazo de batería Google Pixel 4a, Insertar una púa: paso 4, imagen 2 de 3 Reemplazo de batería Google Pixel 4a, Insertar una púa: paso 4, imagen 3 de 3
    • Si tu pantalla está muy agrietada, cubrirla con una capa de cinta de embalar transparente puede permitir que la ventosa se adhiera. También se puede utilizar cinta adhesiva muy resistente en lugar de la ventosa. Si todo lo demás falla, puedes pegar la ventosa a la pantalla rota.

    • Coloca una ventosa lo más cerca posible del borde derecho de la pantalla.

    • Levanta la ventosa fuerte y firmemente.

    • Introduce la punta de una herramienta de apertura en la junta entre la pantalla y el chasis no más de 1 mm.

    It's pretty easy. Insert it just below the screen between the Display and the Display “holder” or mold.

    Aleksandar Dejanovic - Contestar

  5. Reemplazo de batería Google Pixel 4a, Guía la púa bajo el panel OLED: paso 5, imagen 1 de 3 Reemplazo de batería Google Pixel 4a, Guía la púa bajo el panel OLED: paso 5, imagen 2 de 3 Reemplazo de batería Google Pixel 4a, Guía la púa bajo el panel OLED: paso 5, imagen 3 de 3
    • Este paso muestra cómo insertar la púa sin dañar el panel OLED. Haz esto antes de empezar a cortar el adhesivo.

    • Con la púa 1 mm dentro del hueco, gira la púa hacia arriba en un ángulo pronunciado.

    • Con un ángulo pronunciado, empuja con cuidado la púa en el hueco de unos 6 mm. La púa debe deslizarse por debajo del panel OLED.

    • Deténte si sientes que la punta de la púa golpea un borde. La púa puede estar presionando el borde del panel OLED. Inclina la púa e inténtalo de nuevo.

    This took me a while, I ended up sharpening the tip of the pick with a razor so I could push it through the seam and slicing a few times, heat->sharpen-> slice until I finally got it to move, and once it slid under carefully heated up areas and sliced with ~2mm of the pick.

    Alan Carlson - Contestar

    This sounds also harder than it is. Push it in 1mm and just lift the other end in a wider angle like 70° degree from the horinzontal position. There “shouldn't” be much you can do wrong. Because except for the Data cable (flex) at a certain position, I can't remeber anything important but isolating tapes that I have scratched.

    It's just the Screen glued to the mold. That's it.

    Aleksandar Dejanovic - Contestar

    Oh, and I wonder here where do You all get such thins plectrums? I have also the flat plastic version and the thin plastic cards but none of them were thin enough for this!!

    I ended up using the backside i.e. the dull side of a Razorblade. I didn't saw any alternatives to this. Did You hear this OP?

    Any!!

    Aleksandar Dejanovic - Contestar

    the display flex is directly on the bottom of the phone. BE VERY CAREFUL when going around the bottom to not hit the display flex!!!

    FixItAgain - Contestar

  6. Reemplazo de batería Google Pixel 4a, Cortar el adhesivo: paso 6, imagen 1 de 3 Reemplazo de batería Google Pixel 4a, Cortar el adhesivo: paso 6, imagen 2 de 3 Reemplazo de batería Google Pixel 4a, Cortar el adhesivo: paso 6, imagen 3 de 3
    • Desliza la púa por el borde derecho de la pantalla para cortar el adhesivo.

    • No introduzcas la púa más de 6 mm o podría dañar el cable flex de la pantalla.

    • Deja la púa en la esquina superior derecha para evitar que el adhesivo se vuelva a sellar.

    The display flex is directly on the bottom of the phone. Be very careful when goign around the bottom to not hit the display flex!!!

    FixItAgain - Contestar

  7. Reemplazo de batería Google Pixel 4a: paso 7, imagen 1 de 3 Reemplazo de batería Google Pixel 4a: paso 7, imagen 2 de 3 Reemplazo de batería Google Pixel 4a: paso 7, imagen 3 de 3
    • El adhesivo de la pantalla es muy débil y no debería ser necesario volver a aplicar calor. Si la pantalla resulta difícil de cortar, aplica calor en esa zona durante un minuto y vuelve a intentarlo.

    • Introduce otra púa en el borde derecho del teléfono en un ángulo en el que ya se ha formado un hueco para evitar que se dañe el panel OLED.

    • Desliza la púa alrededor de la parte inferior del teléfono para cortar el adhesivo.

    • Hay un delicado cable bajo la esquina inferior derecha de la pantalla. Si notas que tu púa de apertura se engancha en algo, sácala y vuelve a intentarlo. Asegúrese de que la púa está inclinada hacia abajo y que sólo se introduce lo necesario para separar el adhesivo (no más de 2 mm de profundidad).

    • Deja la púa insertada a lo largo del borde inferior para evitar que el adhesivo se vuelva a sellar.

    Top and bottom edge adhesive were much stronger than this suggests. Corners were very hard to detach. I killed my screen b/c I cracked it at the top. Worked better with heating around whole perimeter like an iPhone.

    Erik Sorensen - Contestar

    WARNING: Be very careful prying the bottom left and right corners! In fact do not insert anything there because there is only a 0.8mm clearance between the screen and the edge, and there's a 0.5mm space between the screen and front glass where if you insert a pick between the screen will crack and break! I had to replace the screen after only doing a battery repair...

    bloc - Contestar

    Unfortunately I did not properly read the comments here. So for the unafraid people like me:

    DO NOT insert something into the bottom right! Especially not like it is shown in the image at this location!

    Instead I suggest start releasing the screen from right, then left side, then top and as the last step release the bottom, but start with the left corner. Do not pry too much and use a bit more heat as suggested.

    There is a small image of this critical right corner in Step 16 (the part at the top is the display and the left corner at the top is the critical right corner here). You'll see the orange cable in the corner which is easy to damage...

    Peter - Contestar

    N’allez pas en bas au début faite le haut d’abord j’ai tuer m’on écran

    Jironi - Contestar

    I can second the warnings - especially at the lower corners the OLED screen is extremely sensitive to breaking - as has happened in my attempt when inserting the pick 2 mm.

    Patrick Bohn - Contestar

    The display flex is directly on the bottom of the phone. Be very careful when goign around the bottom to not hit the display flex!!!

    FixItAgain - Contestar

  8. Reemplazo de batería Google Pixel 4a: paso 8, imagen 1 de 3 Reemplazo de batería Google Pixel 4a: paso 8, imagen 2 de 3 Reemplazo de batería Google Pixel 4a: paso 8, imagen 3 de 3
    • Introduce otra púa en el borde inferior en un ángulo en el que ya se ha formado un hueco para evitar que se dañe el panel OLED.

    • Usa la punta de la púa para cortar el borde izquierdo del teléfono.

    • Si resulta difícil cortar el adhesivo, calienta el borde izquierdo durante un minuto y vuelve a intentarlo.

    • Deja la púa insertada a lo largo del borde izquierdo del teléfono para evitar que el adhesivo se vuelva a sellar.

    The display flex is directly on the bottom of the phone. Be very careful when goign around the bottom to not hit the display flex!!!

    FixItAgain - Contestar

  9. Reemplazo de batería Google Pixel 4a: paso 9, imagen 1 de 3 Reemplazo de batería Google Pixel 4a: paso 9, imagen 2 de 3 Reemplazo de batería Google Pixel 4a: paso 9, imagen 3 de 3
    • Hay una malla que cubre el altavoz del auricular en el borde superior de la pantalla. Si no tienes una malla de repuesto, ten cuidado de no dañar o perder este componente.

    • Introduce otra púa en el borde izquierdo del teléfono en un ángulo en el que ya se ha formado un hueco para evitar que se dañe el panel OLED.

    • Desliza la púa alrededor del borde superior del teléfono para cortar el adhesivo.

    • Si resulta difícil de cortar, calienta el borde superior durante un minuto y vuelve a intentarlo.

    The display flex is directly on the bottom of the phone. Be very careful when goign around the bottom to not hit the display flex!!!

    FixItAgain - Contestar

  10. Reemplazo de batería Google Pixel 4a: paso 10, imagen 1 de 2 Reemplazo de batería Google Pixel 4a: paso 10, imagen 2 de 2
    • Una vez que haya cortado el perímetro del teléfono, levanta con cuidado el borde derecho de la pantalla, abriendo el teléfono como un libro.

    • No retires la pantalla todavía.

    • Utiliza una púa para cortar cuidadosamente los restos de adhesivo.

  11. Reemplazo de batería Google Pixel 4a, Dar la vuelta a la pantalla: paso 11, imagen 1 de 3 Reemplazo de batería Google Pixel 4a, Dar la vuelta a la pantalla: paso 11, imagen 2 de 3 Reemplazo de batería Google Pixel 4a, Dar la vuelta a la pantalla: paso 11, imagen 3 de 3
    • Levanta desde el borde superior y gira la pantalla sobre el borde inferior hasta que puedas apoyarla con el lado del cristal hacia abajo.

    • Ten cuidado de no someter a tensión el cable plano conectado.

    FR : Précision : La nappe a un bout d'adhésif sur la structure du téléphone, il faut bien faire attention de le décoller. Je viens de tuer la nappe de mon écran qui était fonctionnel...

    EN : Advice : The ribbon cable is fixed to the structure with a small piece of adhesive. It should be remove prior to anything else. I just killed the ribbon cable of my perfectly used to work screen...

    Arnaud Parrot - Contestar

  12. Reemplazo de batería Google Pixel 4a, Desconectar la pantalla: paso 12, imagen 1 de 1
    • Utiliza unas pinzas para despegar con cuidado la cinta negra que cubre el soporte del conector de la pantalla.

    • Si está en buen estado, puedes reutilizar esta misma cinta durante el reensamblaje. En caso contrario, sustitúyela por un trozo de cinta aislante.

    How critical is the tape that covers this connector? I realized upon sealing back up my device that I forgot to re-install it. I imagine it mostly is there to prevent dust and moisture ingress?

    Alex Cook - Contestar

    Interestingly this tape was missing in my phone. Maybe that explains some of the display issues I occasionally had, like a thin green line on the right side of the screen which could be "pushed" away.

    Fabian Seyfried - Contestar

  13. Reemplazo de batería Google Pixel 4a: paso 13, imagen 1 de 1
    Herramienta utilizada en este paso:
    Magnetic Project Mat
    $19.95
    Comprar
    • Utiliza un destornillador Torx T3 para retirar los dos tornillos de 2,1 mm que fijan el soporte del conector de la pantalla.

    • Durante este paso de la reparación, ten cuidado con todos los tornillos y asegúrate de que los colocas de nuevo en la posición en la que estaban.

    A T4 driver worked for me here.

    Gabe Maayan - Contestar

    It is definitely a T4.

    Jarl Friis - Contestar

    Funny ... For me, it was T3. The screws must vary across different phones

    Helmut Sporgersi - Contestar

  14. Reemplazo de batería Google Pixel 4a: paso 14, imagen 1 de 1
    • Utiliza unas pinzas para retirar el soporte del conector de la pantalla.

    • Asegúrate de guardar este componente para reinstalarlo cuando termines la reparación.

  15. Reemplazo de batería Google Pixel 4a: paso 15, imagen 1 de 2 Reemplazo de batería Google Pixel 4a: paso 15, imagen 2 de 2
    • Utiliza la punta de un spudger para hacer palanca y desconectar el cable flexible de la pantalla.

    • Para volver a colocar los conectores a presión como éste, alinea con cuidado y presiona hacia abajo en un lado hasta que encaje en su sitio, y luego repite en el otro lado. No presiones en el centro. Si el conector está mal alineado, las clavijas pueden doblarse y causar daños permanentes.

    No, why the tip? Use the other flat side that doesn't concetrate all the power on one point and Youre doing a propper job.

    Aleksandar Dejanovic - Contestar

    Only the tip is needed to lift a bit one of the sides and it will pop out. No pressure/power!

    Steve Stavropoulos -

  16. Reemplazo de batería Google Pixel 4a, Quitar la pantalla: paso 16, imagen 1 de 3 Reemplazo de batería Google Pixel 4a, Quitar la pantalla: paso 16, imagen 2 de 3 Reemplazo de batería Google Pixel 4a, Quitar la pantalla: paso 16, imagen 3 de 3
    • Quita la pantalla.

    • Para instalar la pantalla nueva:

    • Verifica si su pantalla de reemplazo tiene una malla de altavoz y adhesivo en el borde superior preinstalados.

    • Si es así, no necesitarás el adhesivo del borde superior.

    • Si no es así, retira el revestimiento transparente más grande del adhesivo del borde superior y aplícalo a la pantalla (no al marco). Asegúrate de que el recorte más grande esté alineado con la malla del altavoz.

    • Sigue esta guía para aplicar el adhesivo de corte personalizado.

    • Utiliza la tercera foto como referencia para colocar sus adhesivos.

    • Durante el proceso de arranque después del reensamblaje, la pantalla pasará por una secuencia de calibración. No toques la pantalla durante este proceso, ya que podrías provocar una calibración táctil inadecuada y crear problemas táctiles.

    This step seems to imply that a screen replacement is necessary when replacing the charging port. Is the charging port replaceable without replacing the screen? I understand great care must be taken not to damage the original screen in the procedure, but can it be reinstalled?

    David-Alexandre Tremblay - Contestar

    Yes, it can be reinstalled.

    Sam Omiotek -

    How long does the calibration process typically take? What does this process look like?

    phelpsbc - Contestar

    Just a heads up: If you are like me and you have accidentally turned on your Pixel 4a at some point while trying to pry the screen, don't worry too much. I was able to just connect my display with the device on. Nothing will happen until you reboot, and then the screen will initialize.

    Alex Cook - Contestar

    It would help to add that the new screen is reattached after adding glue to phone body, not the screen. With the iFixit screen adhesive pieces, a guide to which piece goes where would help also. For that I used this picture: Google Pixel 4a Display Adhesive - Genuine. Yet that is not enough as there is a cover for (speaker?) which is not clear how to apply that.

    markjville - Contestar

    The repair kit comes with Google Pixel 4a Display Adhesive - Genuine but there is no guide on how to apply that adhesive. I sent an email, but Ifixit won't make an instruction page for this.

    Mark - Contestar

    To explain how the adhesive sold by iFixit works, the actual adhesive is the black strip which is held between two pieces of plastic. Line up the pieces with the clear plastic side down. Note that some pieces may be stuck in the box they came in, the plastic is staticky. I recommend that before attaching the new screen you put each piece in place. Remove the clear plastic and place the pieces in place with the colored plastic facing up. The goal is to have the black adhesive strip on the little ledge between the edge and the depression inside the phone. It's the place where you hopefully spent time cleaning out the original adhesive. Place the corners first, then the edges. Press them into place carefully. Before removing the colored plastic attach the phone screen cable and secure it. REMEMBER TO PLACE THE ELECTRICAL TAPE OVER THE CONNECTOR (I forgot to). Then remove the colored plastic, leaving behind the adhesive, and push the screen into place.

    Karzyn - Contestar

    Of note: the seal peace at the top goes under the speaker screen, and the seal looks at first like it is reversed. To install that one accurately adhere it to the Screen itself not the body of the phone. align it where there is a see through circle along the seam and a hole in the adhesive. the sealant should run below the speaker screen. When readhering the screen to the body, remove the plastic guides around the body, then last the seal on the screen and align and install.

    USAF MX - Contestar

    Super, c'est vraiment à la portée de tout le monde, il faut juste un peu de patience et d'audace.

    Je viens de réussir le remplacement de mon écran et c'est impec !

    Il n'y a que sur la première partie, où il faut insérer le médiateur, que ça a été compliqué pour moi. Impossible de l'insérer du côté des boutons (à droite donc), par contre quand je me suis décidée à tester en passant par l'autre côté, c'est venu tout seul.

    Aussi il m'a fallu un certain temps pour comprendre que sur les adhésifs, seul le trait noir colle, et c'est donc à lui qu'il faut faire attention.

    Pensez à vérifier que l'écran est fonctionnel avant de le recoller, à mon premier essai la nappe n'était pas bien insérée et j'ai du recommencer l'insertion. Voila, prendre son temps et vérifier que tout va bien à chaque étape et c'est très facile. J'ai mis un peu moins d'une heure.

    Caroline Leleu - Contestar

    I have no idea what to do with the speaker cover mesh. It is on the display I ordered from fix it, but there is blue plastic tape over it, too, so in order for a speaker to work I'd expect the blue sticky tape needs to be removed, but it nowhere says anything about it.

    deadrom - Contestar

    After I clipped the screen in place, I realized that I had forgotten to reattach the screen bracket from step 14. Do you think this is dangerous? Can anyone assess this? In any case, the smartphone turns on and actually makes a good impression.

    Many thanks in advance for your assessment!

    Kind regards

    Tom

    Timon Roosen - Contestar

    Just some advice before you install the screen regarding the earphone grille/mesh at the top.

    Something I experienced, was that the speaker grille did not end up being seated quite right when the phone display was stuck down. It is slightly bent, and the top edge is stuck out at a slight angle - it is quite sharp and does not take much to catch a finger on it, when the phone is out of a protective case.

    I think this was because I laid the screen in, starting from the top and with it up at quite a steep angle, then working from top to bottom. I would suggest that when setting the new display within the device, that you align the bottom edge first instead.

    I am not going to risk lifting the new display to try and re-seat this grille properly, the display cost me a bloody fortune (around 58% of the phone's original price) and I am not risking breaking it over something as minor as that.

    nb. I definitely removed all the coloured plastic protective pieces before installing the new screen into the phone.

    Andrew - Contestar

  17. Reemplazo de batería Google Pixel 4a, Retirar los tornillos del marco medio: paso 17, imagen 1 de 2 Reemplazo de batería Google Pixel 4a, Retirar los tornillos del marco medio: paso 17, imagen 2 de 2
    • Usa un destornillador Torx T3 para quitar los ocho tornillos de 4,3 mm que sujetan la cubierta posterior al marco medio.

  18. Reemplazo de batería Google Pixel 4a, Separar la tapa trasera del marco medio: paso 18, imagen 1 de 2 Reemplazo de batería Google Pixel 4a, Separar la tapa trasera del marco medio: paso 18, imagen 2 de 2
    • Inserta una púa de apertura en la costura entre el marco medio y la tapa trasera.

    • Desliza la púa de apertura a lo largo del borde inferior del teléfono para liberar los clips de plástico que sujetan la tapa trasera al marco medio.

  19. Reemplazo de batería Google Pixel 4a: paso 19, imagen 1 de 2 Reemplazo de batería Google Pixel 4a: paso 19, imagen 2 de 2
    • Desliza la púa de apertura alrededor del borde izquierdo del teléfono para liberar los clips de plástico que sujetan la tapa trasera al marco medio.

  20. Reemplazo de batería Google Pixel 4a: paso 20, imagen 1 de 3 Reemplazo de batería Google Pixel 4a: paso 20, imagen 2 de 3 Reemplazo de batería Google Pixel 4a: paso 20, imagen 3 de 3
    • Desliza la púa de apertura alrededor de los bordes superior y derecho del teléfono para liberar el resto de los clips.

  21. Reemplazo de batería Google Pixel 4a: paso 21, imagen 1 de 3 Reemplazo de batería Google Pixel 4a: paso 21, imagen 2 de 3 Reemplazo de batería Google Pixel 4a: paso 21, imagen 3 de 3
    • Gira con cuidado la cubierta trasera desde la parte inferior del teléfono sobre la parte superior y alrededor de la parte posterior.

    • Coloca la cubierta posterior sobre la superficie de trabajo y descansa ligeramente el marco medio sobre la cubierta posterior, teniendo cuidado de no ejercer presión sobre los cables planos conectados.

  22. Reemplazo de batería Google Pixel 4a, Retirar el soporte de la placa base: paso 22, imagen 1 de 2 Reemplazo de batería Google Pixel 4a, Retirar el soporte de la placa base: paso 22, imagen 2 de 2
    • Utiliza un destornillador Torx T3 para quitar los siete tornillos que sujetan el soporte de la placa base:

    • Tres tornillos negros de 2,9 mm de largo

    • Tres tornillos de 2 mm de largo

    • Un tornillo de 4,1 mm de largo

  23. Reemplazo de batería Google Pixel 4a: paso 23, imagen 1 de 3 Reemplazo de batería Google Pixel 4a: paso 23, imagen 2 de 3 Reemplazo de batería Google Pixel 4a: paso 23, imagen 3 de 3
    • Usa la punta de un spudger para soltar el soporte de la placa base de las esquinas superior derecha e inferior derecha de la placa base.

    on mine, the fingerprint sensor cable was lightly adherent to the bracket and I almost tore it when the bracket popped up. may want to add something about freeing this up before removing the bracket.

    Erik Sorensen - Contestar

    Similar to Erik, my fingerprint sensor cable was adhered to the bracket and mine did tear. I didn't use the fingerprint sensor, so hopefully this doesn't affect anything else with the phone. Now I know to read the comments! X_X

    Jason Birchard - Contestar

    I found the clip at the top of the bracket very hard to unclip, so much so that it was bending the end of my spudger. In the end I was successful with a spare SIM removal tool instead of a spudger, but in the same manner as pictured in the first 2 photos.

    Adam G - Contestar

    I had the same issues: The cable was attached to the bracket and I had to be very careful in pushing the bracket to the side and reach under it with the spudger to detach the fingerprint cable. And I also found the top clip of the bracket hard to unclip. It worked when I started with the lower one and then pushed the bracket to the side a bit. It seemed to be glued on the top corner.

    Fabian Seyfried - Contestar

    My fingerprint sensor cable was also glued to the bracket, but it seems like a sturdy cable so was not easily damaged

    blueslondon - Contestar

    Ok this was really bad for me I did not understand how the clip was oriented and tried to pull it up lightly first and then strongly, it finally came off but I bent and broke the bridge just a bit, and most importantly the RFID or fingerprint sensor cable (the circle in the back). I don't use it and nothing more was harmed managed to put everything back in place but

    Beware of the clips, you have to pull them TOWARDS you, then the bridge will pop-up, don't apply strength upwards before unclicking the 2 clicks towards you (horizontal plane)

    rkj - Contestar

    This cable also ripped for me as the motherboard bracket popped up! It was remarkably fragile

    IFuxedIt - Contestar

    this is the most frustrating step in the entire guide. i used tweezers and pushed to the left of the upper bracket to free it. no upward force is required to free it. be careful

    Logan Tristan - Contestar

  24. Reemplazo de batería Google Pixel 4a: paso 24, imagen 1 de 3 Reemplazo de batería Google Pixel 4a: paso 24, imagen 2 de 3 Reemplazo de batería Google Pixel 4a: paso 24, imagen 3 de 3
    • Usa un par de pinzas para quitar el soporte de la placa base.

    The cable for fingerprint sensor was slightly glued which I gently removed by using the flat side of the spudger

    Nove - Contestar

  25. Reemplazo de batería Google Pixel 4a, Desconectar la batería: paso 25, imagen 1 de 2 Reemplazo de batería Google Pixel 4a, Desconectar la batería: paso 25, imagen 2 de 2
    • Usa el extremo plano de un spudger para levantar y desconectar el cable de la batería.

  26. Reemplazo de batería Google Pixel 4a, Retirar la tapa trasera: paso 26, imagen 1 de 3 Reemplazo de batería Google Pixel 4a, Retirar la tapa trasera: paso 26, imagen 2 de 3 Reemplazo de batería Google Pixel 4a, Retirar la tapa trasera: paso 26, imagen 3 de 3
    • Usa la punta de un spudger para desconectar los dos cables flexibles que conectan el sensor de huellas dactilares y los botones a la placa base.

  27. Reemplazo de batería Google Pixel 4a: paso 27, imagen 1 de 2 Reemplazo de batería Google Pixel 4a: paso 27, imagen 2 de 2
    • Retira la tapa trasera.

  28. Reemplazo de batería Google Pixel 4a, Retira el adhesivo de la batería: paso 28, imagen 1 de 3 Reemplazo de batería Google Pixel 4a, Retira el adhesivo de la batería: paso 28, imagen 2 de 3 Reemplazo de batería Google Pixel 4a, Retira el adhesivo de la batería: paso 28, imagen 3 de 3
    • Da la vuelta al marco intermedio.

    • Utiliza unas pinzas para retirar los dos trozos de cinta adhesiva negra que cubren las lengüetas adhesivas de la batería.

    • Si los trozos de cinta adhesiva permanecen intactos, vuelve a utilizarlos durante el montaje. En caso contrario, sustitúyelos por cinta aislante.

  29. Reemplazo de batería Google Pixel 4a: paso 29, imagen 1 de 3 Reemplazo de batería Google Pixel 4a: paso 29, imagen 2 de 3 Reemplazo de batería Google Pixel 4a: paso 29, imagen 3 de 3
    • Utiliza unas pinzas para levantar las lengüetas de extracción del adhesivo de la pila y poder cogerlas con los dedos.

    • Ten cuidado de no perforar la batería con las pinzas.

  30. Reemplazo de batería Google Pixel 4a: paso 30, imagen 1 de 3 Reemplazo de batería Google Pixel 4a: paso 30, imagen 2 de 3 Reemplazo de batería Google Pixel 4a: paso 30, imagen 3 de 3
    • Intenta mantener las tiras adhesivas planas y sin arrugas durante este procedimiento; las tiras retorcidas o arrugadas se pegarán y se romperán en lugar de arrancarse limpiamente.

    • Tira lentamente de una de las lengüetas adhesivas de la batería hacia la parte inferior del teléfono.

    • Tira con firmeza, manteniendo una tensión constante en la tira hasta que se deslice entre la batería y el bastidor central. Para obtener los mejores resultados, tira de la tira en un ángulo lo más bajo posible.

    • La tira se estirará hasta varias veces su longitud original. Continúa tirando y vuelve a agarrar la tira cerca de la batería si es necesario.

    • Si las lengüetas adhesivas de la batería se rompen durante el proceso de extracción, utiliza los dedos o unas pinzas sin punta para recuperar el tramo de adhesivo restante y continúe tirando.

    • Si alguna de las tiras adhesivas se ha roto y no se ha podido recuperar, aplica unas gotas de alcohol isopropílico al 90% en la abertura de la pestaña afectada e incline el teléfono hacia el borde superior para que el alcohol fluya hacia el adhesivo restante. Espera un minuto para que el adhesivo se ablande y proceda al siguiente paso.

    Both tapes tore for me after having removed about half of them - they are extremely long. Maybe winding them around a pencil might work better. I had to drop some isopropanol (about 5 drops each) into the holes which worked fine to loosen the remaining adhesive.

    Fabian Seyfried - Contestar

  31. Reemplazo de batería Google Pixel 4a: paso 31, imagen 1 de 1
    • Retira la batería.

    • Si el adhesivo se ha retirado con éxito, la batería debería caer sin problemas.

    • Si la batería no se puede extraer fácilmente, aplica alcohol isopropílico al 90% como se indica en el paso anterior.

    • Una vez que haya dejado pasar un minuto para que el alcohol ablande el adhesivo, utiliza una púa para levantar la pila desde uno de los bordes largos.

    • No dobles la batería.

    Please add instructions for applying the new battery tab adjesives and screen adhesives. I'm afraid "do the steps in reverse" does not work for that part of reassembly.

    drf24k - Contestar

    As the previous commenter suggested, please write instructions for reassembly.

    Guillermo Feliciano - Contestar

    I was thinking the same about the adhesive part… how do you reapply adhesive and the tabs removed? Do we need new adhesive tabs?

    Lucy SterlingEvents Egede - Contestar

    I found a lot of the adhesive remained on the body after removing the strips. I don't know if this is because my battery was swollen and overheating, but I'd expect many people reading this may be in the same situation.

    blueslondon - Contestar

    I was eventually able to figure out re-attache the battery and screen, but as the other commenters have suggested a brief explanation of how to do this would be very helpful.

    Otherwise it was a grate guide!

    Lars Cronje Bjørndal - Contestar

    Another vote for reassembly. There are a lot of adhesive bits with a blue backing which I'm pretty sure are for attaching the screen, but one appears to be a pull tab for the battery (but only 1 not 2). There's also a long strip with a red backing. I have no idea where that one would go. Finally, one of the screen adhesives stuck to the inside of the box so it's unusable now.

    andrea - Contestar

    I just used double sided tape to secure my new battery. just make sure you do a gravity test to make sure it doesn't fall out and shake it around a bit too if you want. read alot of other posts online of people who did the same. ill post back here if something happens but i think it should work fine

    Logan Tristan - Contestar

Conclusión

Para volver a montar el dispositivo, sigue los pasos anteriores en orden inverso.

Lleva tus residuos electrónicos a un reciclador certificado.

¿La reparación no ha ido como estaba previsto? Intenta echar un vistazo a los problemas más comunes, o pide ayuda a en el foro de la Comunidad.

48 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Sam Omiotek

Miembro Desde 02/25/19

71,951 Reputación

288 Guías creadas

29 comentarios

T3 driver is too small. T4 driver fits all screws perfectly.

leehall - Contestar

Do you stock the 4A and 4A 5G batteries? my local repair shops will not just sell me the battery.

Peter Cross - Contestar

Swapped the screen and battery in one go. Did manage to snap the fingerprint sensor cable when removing the motherboard bracket, it popped off a bit fast, but just replaced that too. Thanks for the awesome guide ?

Eric P - Contestar

Thank you - repair went exactly as described for me

rossh - Contestar

Tricky. I don't suggest sweating to save the pieces of tape. Just attach new tape for the battery.

T3 Tip on my kit worked, don't know why it didn't for previous commentor.

Fuwah Chez - Contestar

Which adhesives do I need for this repair?

Azrael - Contestar

Hello Azrael, as noted in the parts section of this guide, you will need Battery Adhesive Strips and Display Adhesive. Both are included in the Google Pixel 4a Battery Fix Kit and available in the iFixit US and EU store.

Manuel Haeussermann -

Thanks.

Do you think using a hair dryer to remove the screen would be better? Or a temperature controlled heat pad? The feedback I read online about the iOpener seems kinda annoying to use.

Azrael -

The iOpener is a good option for most people to make sure to apply heat precisely while making sure to not overheat the device. If you already have a heating mat, that would probably be the best option for controlled heating. A hair dryer should also work quite well, but be careful to avoid overheating.

Manuel Haeussermann -

Thanks! Any idea how easy it is to damage the speaker grills? I saw that the kit has them.

Azrael -

See the following note on step 9: "There's a mesh covering the earpiece speaker on the top edge of the screen. If you don’t have a replacement mesh, take care not to damage or lose this component." You should be careful during the opening procedure, but I'd assume you can reuse it after the repair.

Manuel Haeussermann -

I saw the note, which was why I asked, From experience with certain electronics, there are some components that have an extremely high rate of breaking once you remove it, so was wondering if you had any experience to share.

Azrael -

I don't have hands-on experience with the Pixel 4a, so I'm unable to give a definitive answer, sorry!

Manuel Haeussermann -

Ah, thanks for your help either way!

Azrael -

i'm so sad. i broke my phone trying to install the battery and now the screen just flashes with green lines on it.

Anthony M - Contestar

Unfortunately, my screen cracked a whole bunch from the bottom right corner as I was doing step 6 so I gave up there. There could have been some invisible chips or cracks there already that created a weakness or maybe I just wasn't doing it right. Disappointed, but the kit does seem to be fully featured.

Paige - Contestar

I'm considering replacing the charging port at the same time - what order of operations would you recommend? Things are the same through Step 27, before they diverge. Should I do the battery first, and then continue with the charging port steps? Or the reverse?

C F - Contestar

After finishing the Battery replacement the screen stayed black, it just vibrates short when pressing the power button. charging seems to work since it gets warm. Display did not get damaged when opening, also there was no obvious damages in the areas with the cables.

Any idea what could be the reason for this?

Kai Iskratsch - Contestar

I'm having the same problem. I also see my phone on my wifi network so it does turn on and connect. I just get a black screen though. Any help would be greatly appreciated!

Brian Begun -

Same problem here, Kai and Brian. Can I ask what you did to resolve it?

Ryan Gibb -

Same problem here. Have you solved it by now?

Muckelchen -

Unfortunately after following these steps my screen died, and totally bricked my phone. I suggest backing up, and wiping your phone prior to doing this, just in case, if you want to sell it as a broken phone after that, at least it won't have your data on it.

SteveF - Contestar

REALLY wish all the comments about the screen going black had been showing prior to my starting this procedure... It looks like they were there, but you need to dig in to them.

SteveF - Contestar

FAILED. Phone vibrates once when I try to turn it on. Display stays black

Che Guevara - Contestar

I successfully replaced the battery on my Pixel 4.
Unfortunately, after I replaced the battery on my Pixel 4a (which is slightly different) the screen stayed black.
I can hear my phone respond when I plug in the charger and the phone vibrates when I use the finger sensor.

Albert - Contestar

I had significant difficulty with the battery adhesive tabs just not pulling away. If you remove the large black piece of tape on the back of the metal midframe it will expose more of the back of the battery. There is a cutout which runs parallel to the two lines of adhesive. I used goo gone and very light cyclic pressure to gently weaken the adhesive strips and ultimately remove the battery.

Ryan - Contestar

It took me about 3 hours to do it: cleaning the glue took some time and I was very scared to break the screen at the beginning.
A tuto to show how to place the stickers with glue would have been nice.
A big thank you in the end, I did it, it works and I'm super proud!!

Mickaël N - Contestar

So this is probably the first time i fcked up my own phones screen. The display flex is directly on the bottom of the phone. be very careful when goign around the bottom to not hit the display flex!!!

I would guess that this is why the blacksreens are appearing.

FixItAgain - Contestar

sadly I am also the one failed. The screen stays black without any cracks or other visible damage

Artem Goncharov - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 134

Ultimos 7 días: 936

Ultimos 30 días: 4,110

Todo El Tiempo: 102,569