Saltar al contenido principal

Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.

Qué necesitas

  1. , Pantalla: paso 1, imagen 1 de 3 , Pantalla: paso 1, imagen 2 de 3 , Pantalla: paso 1, imagen 3 de 3
    • Toma nota de las dos juntas en el teléfono:

    • Juntura de la pantalla: Esta juntura separa la pantalla del resto del teléfono. Es aquí donde deberías hacer palanca.

    • Juntura del marco: Esto es donde el marco de plástico se junta con la tapa trasera. Se sujeta en su lugar mediante tornillos. No hagas palanca en esta juntura.

    • Antes de empezar a hacer palanca, ten en cuenta las siguientes áreas de la pantalla:

    • Cable flexible de la pantalla: No hagas palanca más allá de lo indicado o correras el riesgo de dañar este cable.

    • Perímetro del adhesivo: Si haces palanca más allá del perímetro estrecho sin inclinar la púa, se dañará la pantalla .

    Power is off, but does the battery need to be disconnect to safely do this replacement?

    mplishka - Contestar

    Da ich keinen iopener ( dachte das wäre alles dabei wie auf der bstellvorschau!!!) habe ich eine Wärmflasche auf das Handy gelegt ..behutsam und nicht zu heiß. Besonders an Kopf und fußende war das Display ziemlich fest...befolgt man die Anweisungen genau ist es eigentlich kein Problem das Display vom Rahmen zu lösen, jedoch bin ich der Meinung, dass hier schon ein gewisses Maß an motorischer Vertrautheit mit der Materie bestehen sollte, da wie gesagt oben und unten doch ein tieferes eingreifen in den Rahmen unter das Display nötig ist...

    Ralph S. aus Neumünster

    Ralph S - Contestar

    You definitely want to use the iOpener on all sides as you make your way around the screen. The adhesive on my device was quite strong!

    My screen was cracked in the corner and it was a real pain in the neck to get the little bits and pieces out of the corner. I don't know if this step is easier with an intact screen, but it was definitely the most difficult step on the repair for me.

    Simon Stone - Contestar

  2. : paso 2, imagen 1 de 1
    • Calienta un iOpener y aplícalo al borde derecho de la pantalla durante un minuto

    • Puedes optar por omitir este paso ya que el adhesivo para pantallas de Pixel 3a no es muy fuerte. Calentarlo, sin embargo, disminuirá la posibilidad de agrietar la pantalla.

    I used a washcloth soaked with hot water and sealed in a plastic bag instead of the iOpener for this step, and it worked great.

    E. Dunham - Contestar

    My screen was cracked diagonally. Heating with iOpener helped at the top and bottom edges to weaken the adhesive.

    Károly Varga - Contestar

  3. : paso 3, imagen 1 de 3 : paso 3, imagen 2 de 3 : paso 3, imagen 3 de 3
    • Coloca una ventosa cerca del borde derecho de la pantalla.

    • Tira de la ventosa con fuerza constante.

    • Inserta la púa en la grieta , no más de 1 mm.

  4. : paso 4, imagen 1 de 3 : paso 4, imagen 2 de 3 : paso 4, imagen 3 de 3
    • Este paso muestra cómo insertar la púa sin dañar el panel OLED. Haz esto antes de cortar los borders largos del teléfono.

    • Con la púa 1 mm dentro de la grieta, gira la púa hacia arriba hasta un ángulo pronunciado.

    • En este ángulo, empuja cuidadosamente la púa en el espacio aproximadamente 6 mm. La púa debe deslizarse por debajo del panel OLED.

    • Deténte si sientes que la punta de la púa golpea un borde. La púa puede estar presionando contra el borde del panel OLED. Inclina la púa e inténtalo de nuevo.

    If you don’t have picks, you can also use the corner of an old gift card, though it may be necessary to shave it a bit thinner with a knife so it fits the gap better.

    E. Dunham - Contestar

  5. : paso 5, imagen 1 de 3 : paso 5, imagen 2 de 3 : paso 5, imagen 3 de 3
    • Desliza la púa a lo largo del borde derecho, cortando el adhesivo.

    • No insertes las púa más de 6 mm, ya que podrías dañar el cable flexible de la pantalla.

    • Deja una púa en su lugar para que el adhesivo se vuelva a sellar.

    Don’t make my mistake and read ahead. 6mm may be too close for comfort! 8mm is definitely too far and caused me to damage. Also be sure to read the right manual! I have an XL and it notes 5mm.

    Miguel Higgins-Moy - Contestar

    Fortunately my old screen was beyond repair, But be super careful around the bottom I managed to sever the ribbon cable to the digitizer.

    Stephen Hammons - Contestar

    I broke my screen here. The adhesive in my case was quite strong on the top and bottom.

    Mario Flores - Contestar

    This is by far the hardest part of the entire replacement. I ruined my screen doing this, you might as well buy a new screen at the same time as you buy your battery. I just barely rubbed the edges of my screen and it turned the edge of my screen purple. This eventually migrated to the entire screen causing the whole thing to be purple/black.

    Ross Lancaster - Contestar

    Hard to not make a mistake here. It's more like 1/8". It's difficult to keep the pick at a steep angle at all times on left and right sides.

    Won Choi - Contestar

    I've repaired many iPhones, and never had any issues. The screens always remained intact. But with the Pixel, I completely destroyed the screen. The only thing it showed after booting up was a purple line... The adhesive is very strong and it's nearly impossible to separate the screen without damaging it. You should order a new screen before you attempt to change the battery, just in case.

    Philipp - Contestar

  6. : paso 6, imagen 1 de 3 : paso 6, imagen 2 de 3 : paso 6, imagen 3 de 3
    • Al cortar alrededor del borde inferior del teléfono, no insertes a la púa más de 6 mm.

    • Desliza la púa por la esquina inferior derecha para cortar el adhesivo.

    • Si la esquina se siente difícil de cortar, aplica un iOpener caliente a la esquina durante un minuto e inténtalo de nuevo.

    • Continúa cortando a lo largo del borde inferior del teléfono y a la vuelta de la esquina izquierda.

    Heating bottom of the screen and going very slowly is key here. The adhesive was stronger than expected, and I cracked the glass while going around this first corner.

    Jerome C - Contestar

    My screen was already cracked diagonally, so going around the corners was especially hard. Starting from each side was not so risky as I first thought because side adhesive is really thin. However top and bottom needed some more lifting force from the pick. More heating helped at the top and bottom edges.

    Károly Varga - Contestar

  7. : paso 7, imagen 1 de 3 : paso 7, imagen 2 de 3 : paso 7, imagen 3 de 3
    • Corta a través del borde izquierdo del teléfono, asegurándote de inclinar correctamente la púa debajo del panel OLED e insértela no más de 6 mm.

    • Para inclinar la púa debajo del panel OLED, inserta la punta de la púa no más de 1 mm, inclina la púa hacia arriba, y luego empuja lentamente la púa 6 mm.

  8. : paso 8, imagen 1 de 3 : paso 8, imagen 2 de 3 : paso 8, imagen 3 de 3
    • Corta a lo largo del borde superior mientras mantienes la púa no más de 8 mm adentro.

    There is a LOT more adhesive at the top than anywhere else on the phone! It’s like there’s 2 lines of adhesive, one along the edge of the case and one along the edge of the screen, and it’s filled in between them wherever the speaker camera aren’t. I needed to heat and pry several times to get the top loose. Fortunately, there’s little risk of hitting a cable near the top (look ahead to the step where you lift the screen off to see where all the cables go!)

    E. Dunham - Contestar

    I found that applying the iOpener across the top edge of the glass for about 30 seconds at this step helped soften the adhesive significantly. My front camera was replaced only a few months ago by uBreakiFix and the display adhesive subsequently let go on the entire right edge, bottom, and part of the left side shortly after the new front camera failed. Only the top was still securely stuck.

    Reid Solberg - Contestar

  9. : paso 9, imagen 1 de 2 : paso 9, imagen 2 de 2
    • Con todos los bordes cortados, abre con cuidado el borde derecho de la pantalla.

    • No quites la pantalla. Sigue conectado al teléfono mediante un cable flexible cerca del borde izquierdo.

    • Utiliza una púa de apertura para cortar con cuidado cualquier resto de adhesivo.

  10. : paso 10, imagen 1 de 3 : paso 10, imagen 2 de 3 : paso 10, imagen 3 de 3
    • Con todos los adhesivos cortados, voltea el vidrio de la pantalla hacia abajo y colócalo en la parte superior del teléfono. El cable flexible de la pantalla debe estar ligeramente arqueado.

    Hi, could you help me with one clarification?

    What does the small “metal patch” in the middle of the display ribbon do?

    Does it prevent the phone from starting while disconnected?

    Thank you for your time!

    oliver schirmer - Contestar

    Hi Oliver,

    I think the patch you’re referring to helps with either EM shielding or heat dissipation. It should not prevent the phone from starting.

    Arthur Shi -

  11. : paso 11, imagen 1 de 3 : paso 11, imagen 2 de 3 : paso 11, imagen 3 de 3
    • Despega cuidadosamente la cinta negra que cubre el soporte del conector de la pantalla.

    • Si está en buenas condiciones, puedes reutilizar esta cinta durante el reensamblaje. De lo contrario, reemplázalo con un trozo de cinta adhesiva eléctrica.

    • Retira los dos tornillos T3 de 4.4 mm de largo que fijan el soporte del conector de la pantalla.

    • Retira el soporte del conector de la pantalla.

    This may be a silly question but how are you able to tell whether the tape is in good condition? Is it based off of how sticky it is after you remove it?

    Sylvia - Contestar

    That is a fair question! If the tape is in one piece and is relatively sticky, it can probably be used again.

    Arthur Shi -

    Oops! I forgot to put any tape back. Does this tape have a critical purpose, in other words should I go to the trouble to pry the screen back off and tape it?

    elyze - Contestar

    The tape does not serve a critical purpose. If you have already re-sealed your phone, I wouldn’t worry about it.

    Arthur Shi -

    Les vis sont des T4 et non des T3

    Gaëtan PERRIER - Contestar

    Bonjour Gaëtan ! Merci pour la remarque. En fait, il y a toujours une certaine tolérance entre le tournevis et la tête de vis. Donc il se peut que la taille supérieure ou inférieure soit plus “confortable” au cas par cas. Bonne réparation !

    Claire Miesch -

    Bonjour,

    Pouvez-vous me conseiller un bon kit de réparation pour mon Google Pixel 3A?

    J'ai peur de me faire arnaquer en achetant un mauvais écran de basse qualité .

    mailsecoursd - Contestar

    In 2023, (along with the USB-C port and screen adhesive) this repair kit includes a new piece of black tape to cover the connector bracket.

    nelson - Contestar

    Do you sell the 2 4.4mm t3 screws and the screen connector bracket. Or know where I can get it thanks

    Brett Bellesbach - Contestar

  12. : paso 12, imagen 1 de 2 : paso 12, imagen 2 de 2
    • Usa la punta de un spudger para entrometerse y desconectar el cable flexible de la pantalla.

    • Cuando desconectes conectores como estos, ten cuidado de no desalojar los pequeños componentes montados en la superficie que rodean el zócalo.

    • Para volver a colocar los conectores de presión como éste, alinea y presiona con cuidado en un lado hasta que encaje en su lugar, luego repite en el otro lado. No presiones hacia abajo en el centro. Si el conector está desalineado, los pines pueden doblarse, causando daños permanentes.

    I had accidentally pressed the power button and the phone was on when connecting the new screen and that broke the board! So make sure the phone is off.

    Diako Mardanbegi - Contestar

    hey man think I've just done the same thing :(

    how did you fix it? did it need a new motherboard?

    Ben Willshaw -

    is it okay if I forgot to add the black tape on the connector area???

    Harry Banda - Contestar

    When reassembling, before reattaching the connector for the screen flex cable is the time to align the screen cover adhesive sheet onto the perimeter of the plastic mid-frame. Even if one is using the Tesa tape, I suspect aligning it along the edge of the mid-frame would be simpler without the screen and its flex cable obstructing your efforts.

    nelson - Contestar

  13. : paso 13, imagen 1 de 3 : paso 13, imagen 2 de 3 : paso 13, imagen 3 de 3
    • Remueve la pantalla.

    • Con atención compara tu pantalla de reemplazo con tu pieza original. Podrías necesitar transferir componentes adicionales (como la malla del auricular) a la nueva pieza.

    • Para volver a instalar la pantalla:

    • Sigue esta guía si estás usando adhesivos personalizados.

    • Si estás usando cinta de doble cara (como la cinta de marca Tesa), usa esta guía

    • Durante el proceso de arranque después del reensamblaje, la pantalla pasará por una secuencia de calibración. No toques la pantalla durante este proceso, ya que podrías provocar una calibración táctil incorrecta y crear problemas táctiles.

    There is a blue plastic tape covering the digitizer and when I try to take it off it rips out something more than just the tape I think it’s pulling the magnet too

    Darien Suarez - Contestar

    i had a little plastic piece around the camera (seems to just be a spacer) that i moved to the new screen. had to pry it up with a pick cuz it was stuck down good.

    elyze - Contestar

    actually to clarify- i didn’t move the little camera spacer to the new screen- i placed it around the camera on the phone, where there was a little indent for it, and stuck it down with a bit of tesa strip, then applied more tesa strips around the edge of the phone before finally reconnecting and replacing the screen. the little plastic bit i encountered needs to be precisely placed around the camera so would not be a good idea to just stick it to the screen when reinstalling!

    elyze -

    Thanks team! I was able to replace my broken screen with no issues!

    Instead of cutout adhesives or tesa tape, I used B-7000. Painless.

    Appreciate the screen and instructions!

    Jessica Hale - Contestar

    Bonjour,

    Pouvez-vous me conseiller un bon kit de réparation pour mon Google Pixel 3A?

    J'ai peur de me faire arnaquer en achetant un mauvais écran de basse qualité .

    Hello . Can you advice me a site where i Can buy a quality screen replacement pack for my Google Pixel 3A?

    There's a lot of rip off on internet and id like to get a good pack and a quality screen .

    Bichette Laterreur - Contestar

    Hello! We currently sell a replacement screen. However, I’m not sure if it is available yet internationally.

    Arthur Shi -

    I have a quick question, so I haven’t done anything yet because I only just ordered my repair kit, but is it possible to replace the battery without having to replace the display ?

    Braeden - Contestar

    Hi Braeden!

    Yes, it is definitely possible to replace the battery without replacing the display. With that said, the initial entry steps can be pretty tricky. Before you begin, look very closely over the display to see if you can see any micro-fractures. If you see any, you will most likely crack the screen when you try to remove it. Take your time and apply a heated iOpener often. Good luck!

    Arthur Shi -

    I forgot to order the tape when getting my replacement USB port, so I ended up putting the screen back on without any tape and using regular clear tape on the outside of the phone to keep the screen from falling off. It’s less waterproof, but it’ll do the job until the right part arrives.

    E. Dunham - Contestar

    Speaker mesh appeared to already be in place on my replacement screen, so I did not transfer this over from my old screen. That was a huge mistake, sounds were garbled above about 30% volume. Make sure you do this part!

    Evan Heisman - Contestar

    Shall I place the adhesive onto the screen or onto the body when placing the new screen? It is not clear from the guides.

    HoundRock - Contestar

    I tried the replacement after watching this and many other videos. I purchased a working Pixel 3a and removed it to put onto my old Pixel 3a. The screen is not turning on on either devices now, old or new. The device is turning on because I can feel vibrations. What do you think the problem is?

    InnLing Eng - Contestar

  14. , Marco medio de plástico: paso 14, imagen 1 de 1
    Herramienta utilizada en este paso:
    Magnetic Project Mat
    $19.95
    Comprar
    • Remueve los catorce tornillos T3 de los siguientes largos que sujetan el marco medio de plástico:

    • Doce tornillos T3 plateados de 4.3 mm

    • Dos tornillos T3 negros de 4.3 mm

    • A lo largo de esta reparación, realiza un seguimiento de cada tornillo y asegúrate de que vuelva exactamente al lugar de donde vino.

    I found that a T3 bit didn’t get purchase on the screws in my Pixel 3a, but the T4 bit worked great. Not sure what’s up with that.

    E. Dunham - Contestar

    This is definitely possible, depending on which kit’s T3 bit you use, along with potential screw quality variances.

    Arthur Shi -

    My Pixel 3a has been apart three times for a non-functioning front camera. The first time, it was by a Google authorized repair shop, and the camera stopped functioning again after a few months. When I took it apart the second time, I noted that many of the screws weren't seated before I removed them. The camera module had become disconnected and simply reseating the connector fixed it. I was careful to fully drive all screws and apply an appropriate amount of torque to them, thinking the repair shop failed to do so. After 9 or 10 months, my front camera stopped working again. Again, I'm noticing a lot of the screws have worked themselves loose. I'm going to try to find an appropriate thread compound that I can precisely apply to these tiny screws.

    Reid Solberg - Contestar

    Hey Reid,

    I would suggest blue Loctite or threadlocker. Dab a small drop on each screw before you install them.

    Arthur Shi -

    One of the bolts was rounded, so the torx screwdrivers (T3 or T5 in the kit) couldn't bite and loosen it. Not sure how to go forward.

    Won Choi - Contestar

  15. : paso 15, imagen 1 de 3 : paso 15, imagen 2 de 3 : paso 15, imagen 3 de 3
    • El marco medio se mantiene en su lugar mediante clips de plástico.

    • Inserta una púa de apertura en la juntura del marco en la parte inferior del teléfono. Esta costura se encuentra entre el marco medio de plástico y la tapa trasera.

    • Desliza la púa a lo largo de la costura para soltar los clips que sujetan el marco medio de plástico.

    To remove the midframe, I was having a lot of trouble until removing the sim card tray. I think this might have to be removed before the midframe

    Elijah Kennedy - Contestar

  16. : paso 16, imagen 1 de 3 : paso 16, imagen 2 de 3 : paso 16, imagen 3 de 3
    • Desliza la púa de apertura a lo largo de los bordes izquierdo y derecho del teléfono para liberar los clips del marco medio.

    • Levanta el borde inferior del marco medio de plástico pero no lo quites. El marco medio todavía está atada al teléfono por el frágil cable del sensor de proximidad en el borde superior.

    • Para volver a instalar el marco medio de plástico, alinea el marco medio con la tapa posterior y aprieta el perímetro del teléfono con los dedos para volver a colocar los clips en su posición.

  17. : paso 17, imagen 1 de 3 : paso 17, imagen 2 de 3 : paso 17, imagen 3 de 3
    • Utiliza la punta de un spudger para hacer palanca con cuidado y desconectar el conector del sensor de proximidad de la placa madre.

    • Es posible que el conector del sensor de proximidad se haya desconectado automáticamente cuando levantaste el marco medio.

    • Remueve el marco medio de plástico.

    This connector is f*ckn impossible to reconnect 😭

    Arnau Mora - Contestar

    This is the hardest part of the job. I gave up on connecting the proximity sensor while in the midframe, and found it much easier to remove the proximity sensor from the midframe, attach the connector, then thread the sensor into its home in the midframe.

    Steve Williams - Contestar

  18. : paso 18, imagen 1 de 3 : paso 18, imagen 2 de 3 : paso 18, imagen 3 de 3
    • Este paso muestra cómo volver a conectar el sensor de proximidad durante el montaje.

    • Alinea el borde superior del marco medio de plástico con el teléfono.

    • Utiliza la punta de un spudger para alinear y empujar cuidadosamente el conector del sensor de proximidad en el zócalo de la placa madre.

    • Esto requiere un poco de paciencia y delicadeza. Una vez que tengas el conector en su lugar, también puedes utilizar un dedo para presionar suavemente el conector en el zócalo.

    • Si lo prefieres, puedes quitar el sensor de proximidad del marco medio para volver a fijarlo primero a la placa madre.

    • Usa la punta de un spudger para sacar con cuidado el sensor de proximidad de su hueco en el marco medio. El sensor está ligeramente adherido al marco medio.

    • Retira el sensor del marco medio. Conecta el conector del sensor en el zócalo de la placa madre.

    • Pasa el cable del sensor a través del marco medio y reposiciona el sensor en el hueco. Presiona hacia abajo con el dedo para volver a adherir el sensor al marco medio.

    I tried to do this for about 15 minutes before I went to the alternative. There is a tiny post to hold the sensor in position on the midframe. I pried the sensor from the midframe from the corner opposite that post and then finished this step in 2 minutes.

    jason.naylor - Contestar

    Definitely plan b for reconnecting the proximaty sensor…

    noel - Contestar

    Plan B ok for me as well. There is a hole below the sensor in order to push it with a sim card opener.

    Laurent GUILLOT - Contestar

    Definitely plan B

    Tom Heath - Contestar

    Plan B here as well. Also +1 for Laurent GUILLOT's hint.

    Paul Kube - Contestar

  19. , Desconexión de la batería del Google Pixel 3a: paso 19, imagen 1 de 3 , Desconexión de la batería del Google Pixel 3a: paso 19, imagen 2 de 3 , Desconexión de la batería del Google Pixel 3a: paso 19, imagen 3 de 3
    • Utiliza la punta de un spudger para entrometerse y desconectar el conector de la batería del zócalo de la placa madre.

    • Dobla el cable flexible de la batería ligeramente para que no haga contacto accidentalmente con el zócalo.

  20. Este paso está sin traducir. Ayuda a traducirlo

    : paso 20, imagen 1 de 3 : paso 20, imagen 2 de 3 : paso 20, imagen 3 de 3
    • Use the point of a spudger to pry up and disconnect the rear facing camera connector from its motherboard socket.

    • Remove the rear facing camera.

Linea de Meta

4 personas más completaron esta guía.

Arthur Shi

Miembro Desde 01/03/18

248,412 Reputación

503 Guías creadas

Equipo

iFixit Miembro de iFixit

Staff

136 Miembros

16,562 Guías creadas

5 comentarios

Do you think it’s still worth attempting this repair if I have a 2” crack at the bottom of my glass? The LCD is still intact. Looks like there’s a spot/scratch on my camera sensor, and I’d like to replace it, but I suppose I’d rather have the screen intact than the camera repaired.

Thomas Domingo - Contestar

Hi Thomas,

I think that if you attempt to remove the screen, the top glass will crack significantly more. You can get the top glass replaced, but due to the fragility of the LCD panel, I would suggest a repair shop for that kind of work.

Arthur Shi -

Would it be possible to carefully use heat-gun instead of the IOpener? Or do you think it would be too risky over heating and damaging the display or other component of the phone? I want to do the fix myself with IFixits essential tool kit, I already have the heat gun. Thanks for your advice!

Nathan Travanti - Contestar

Hey Nathan,

You can definitely use a heat gun. Be very careful as the OLED panel is susceptible to heat damage.

Arthur Shi -

Whew. That was a challenge. But I now have a working rear camera on my 3A. Thanks to iFixit for making this possible.

Assembling step 11, I forgot to apply the tape over the screen connector. Everything works tho, at least for now...

Paul Kube - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 3

Ultimos 30 días: 38

Todo El Tiempo: 3,936