Saltar al contenido principal

GoPro Hero5 Black Battery Housing Replacement

Qué necesitas

  1. GoPro Hero5 Black Battery Housing Replacement, Battery: paso 1, imagen 1 de 3 GoPro Hero5 Black Battery Housing Replacement, Battery: paso 1, imagen 2 de 3 GoPro Hero5 Black Battery Housing Replacement, Battery: paso 1, imagen 3 de 3
    • While pressing the button on the bottom of the GoPro, slide the battery door to the side to pop it open.

  2. GoPro Hero5 Black Battery Housing Replacement: paso 2, imagen 1 de 3 GoPro Hero5 Black Battery Housing Replacement: paso 2, imagen 2 de 3 GoPro Hero5 Black Battery Housing Replacement: paso 2, imagen 3 de 3
    • Grab the plastic flap on the battery and pull the battery out.

  3. GoPro Hero5 Black Battery Housing Replacement, Back Housing: paso 3, imagen 1 de 2 GoPro Hero5 Black Battery Housing Replacement, Back Housing: paso 3, imagen 2 de 2
    • Pull and twist the lens cover right or left until it pops off.

    • The lens cover is secured tightly and might be difficult to twist off.

    レンズを回すには爪などをレンズカバーと本体との隙間に入れて、手前に引き出してから回転させます。

    Taizo Yamamoto - Contestar

    Go around the gap between the lens cover and camera body with a thin spludger to open a small gap and the cover will twist off easily.

    Paul - Contestar

  4. GoPro Hero5 Black Battery Housing Replacement: paso 4, imagen 1 de 1
    • This step is not necessary but will make the process of removing the faceplate much easier.

    • Refer to the iOpener instructions for how to heat up and use the iOpener.

    • Apply the heated iOpener to the front of the GoPro for a few minutes to melt the adhesive under the faceplate.

    • The heated iOpener is very hot and can burn your hands. Avoid burns by using towels or gloves to hold the iOpener.

  5. GoPro Hero5 Black Battery Housing Replacement: paso 5, imagen 1 de 3 GoPro Hero5 Black Battery Housing Replacement: paso 5, imagen 2 de 3 GoPro Hero5 Black Battery Housing Replacement: paso 5, imagen 3 de 3
    • Starting with the edges, use the spudger to pry off the faceplate.

    • The faceplate is held down with adhesive and may take a while to get off.

  6. GoPro Hero5 Black Battery Housing Replacement: paso 6, imagen 1 de 2 GoPro Hero5 Black Battery Housing Replacement: paso 6, imagen 2 de 2
    • Remove the six T3 Torx screws.

    Where can I get the screw driver

    subashzeeq - Contestar

    Mine are actually T4 screws.

    John Hahn - Contestar

  7. GoPro Hero5 Black Battery Housing Replacement: paso 7, imagen 1 de 3 GoPro Hero5 Black Battery Housing Replacement: paso 7, imagen 2 de 3 GoPro Hero5 Black Battery Housing Replacement: paso 7, imagen 3 de 3
    • Be careful when pulling open the motherboard assembly as it is still connected to the back housing by four cables. The cables may break if stretched.

    • Using the spudger, slowly pry open the motherboard assembly from the LCD side of the GoPro.

    Little FYI ; pry slightly on the side with the LCD. Once it pops, work the other slightly. Then pull the board up and out but remember the cables. THE PICTURE ABOVE WHERE THE METAL SHIELD IS IS THE CAMERA LENS! CABLES ARE ON THE SIDE WHERE YOU BEGIN PRYING.

    stevan othon - Contestar

  8. GoPro Hero5 Black Battery Housing Replacement: paso 8, imagen 1 de 3 GoPro Hero5 Black Battery Housing Replacement: paso 8, imagen 2 de 3 GoPro Hero5 Black Battery Housing Replacement: paso 8, imagen 3 de 3
    • Use the flat end of a spudger to pry the three ribbon cables connected to the side of the motherboard.

  9. GoPro Hero5 Black Battery Housing Replacement: paso 9, imagen 1 de 2 GoPro Hero5 Black Battery Housing Replacement: paso 9, imagen 2 de 2
    • Use the flat end of the spudger to pry the battery housing power cable straight up from its socket on the motherboard.

    Does anyone know which are the specs of the connector/socket? Thanks

    Pietro De Caro - Contestar

  10. GoPro Hero5 Black Battery Housing Replacement, Battery Housing: paso 10, imagen 1 de 1
    • Remove the 3mm #000 Phillips screw.

    • Remove the 2mm #000 Phillips screw.

  11. GoPro Hero5 Black Battery Housing Replacement: paso 11, imagen 1 de 1
    • Use the tweezers to grasp the housing firmly and pull it away from the three ribbon cables.

    • Pull the battery housing until the half circle grooves on the back housing match up with the grooves on the battery housing.

    • After the screws have been removed from the inside, the battery housing is only held down by adhesive.

  12. GoPro Hero5 Black Battery Housing Replacement: paso 12, imagen 1 de 2 GoPro Hero5 Black Battery Housing Replacement: paso 12, imagen 2 de 2
    • Make sure the half circle grooves match up. Otherwise the battery housing will not be able to be pulled out.

    • With your fingers, push from the inside of the battery compartment and pull the battery housing out from the back housing.

Conclusión

To reassemble your device, follow these instructions in reverse order.

10 personas más completaron esta guía.

Equipo

Cal Poly, Team 18-6, Forte Fall 2016 Miembro de Cal Poly, Team 18-6, Forte Fall 2016

CPSU-FORTE-F16S18G6

4 Miembros

22 Guías creadas

Un comentario

Is there any glue to use to make the case waterproof again?

Dominik Lisiakiewicz - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 9

Ultimos 30 días: 67

Todo El Tiempo: 12,896