Repara tus cosas Comunidad Tienda

Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.

Escrito Por: Christopher Adams (y otros 8 participantes)
  • Comentarios: 7
  • Favoritos: 1
  • Terminaciones: 14

Dificultad

Moderado

Pasos

9

Tiempo Requerido

10 - 15 minutos

Secciones

2

  • 2 Pasos
  • 7 Pasos

Banderas

0

  1. Este paso está sin traducir. Ayuda a traducirlo

    While pressing the button on the bottom of the GoPro, slide the battery door to the side to pop it open. While pressing the button on the bottom of the GoPro, slide the battery door to the side to pop it open. While pressing the button on the bottom of the GoPro, slide the battery door to the side to pop it open.

    • While pressing the button on the bottom of the GoPro, slide the battery door to the side to pop it open.

    Traducir

  2. Este paso está sin traducir. Ayuda a traducirlo

    Grab the plastic flap on the battery and pull the battery out. Grab the plastic flap on the battery and pull the battery out. Grab the plastic flap on the battery and pull the battery out.

    • Grab the plastic flap on the battery and pull the battery out.

    Traducir

  3. Este paso está sin traducir. Ayuda a traducirlo

    Pull and twist the lens cover right or left until it pops off. The lens cover is secured tightly and might be difficult to twist off.

    • Pull and twist the lens cover right or left until it pops off.

    • The lens cover is secured tightly and might be difficult to twist off.

    Traducir

  5. Este paso está sin traducir. Ayuda a traducirlo

    This step is not necessary but will make the process of removing the faceplate much easier.

    • This step is not necessary but will make the process of removing the faceplate much easier.

    • Refer to the iOpener instructions for how to heat up and use the iOpener.

    • Apply the heated iOpener to the front of the GoPro for a few minutes to melt the adhesive under the faceplate.

    • The heated iOpener is very hot and can burn your hands. Avoid burns by using towels or gloves to hold the iOpener.

    Traducir

  6. Este paso está sin traducir. Ayuda a traducirlo

    Starting with the edges, use the spudger to pry off the faceplate. The faceplate is held down with adhesive and may take a while to get off. The faceplate is held down with adhesive and may take a while to get off.

    • Starting with the edges, use the spudger to pry off the faceplate.

    • The faceplate is held down with adhesive and may take a while to get off.

    Traducir

  7. Este paso está sin traducir. Ayuda a traducirlo

    Remove the six T3 Torx screws. Remove the six T3 Torx screws.

    • Remove the six T3 Torx screws.

    Traducir

  8. Este paso está sin traducir. Ayuda a traducirlo

    Be careful when pulling open the motherboard assembly as it is still connected to the back housing by four cables. The cables may break if stretched. Using the spudger, slowly pry open the motherboard assembly from the LCD side of the GoPro. Using the spudger, slowly pry open the motherboard assembly from the LCD side of the GoPro.

    • Be careful when pulling open the motherboard assembly as it is still connected to the back housing by four cables. The cables may break if stretched.

    • Using the spudger, slowly pry open the motherboard assembly from the LCD side of the GoPro.

    Traducir

  9. Este paso está sin traducir. Ayuda a traducirlo

    Use the flat end of a spudger to pry the three ribbon cables connected to the side of the motherboard. Use the flat end of a spudger to pry the three ribbon cables connected to the side of the motherboard. Use the flat end of a spudger to pry the three ribbon cables connected to the side of the motherboard.

    • Use the flat end of a spudger to pry the three ribbon cables connected to the side of the motherboard.

    Traducir

  10. Este paso está sin traducir. Ayuda a traducirlo

    Use the flat end of the spudger to pry the battery housing power cable straight up from its socket on the motherboard. Use the flat end of the spudger to pry the battery housing power cable straight up from its socket on the motherboard.

    • Use the flat end of the spudger to pry the battery housing power cable straight up from its socket on the motherboard.

    Traducir
Linea de Meta

14 personas más completaron esta guía.

Autor

con 8 otros colaboradores

Christopher Adams

Miembro Desde 03/10/16

1,976 Reputación

5 Guías creadas

Insignias: 18

+ 15 más insignias

Equipo

Cal Poly, Team 18-6, Forte Fall 2016 Miembro de Cal Poly, Team 18-6, Forte Fall 2016

CPSU-FORTE-F16S18G6

4 Miembros

18 Guías creadas

2 comentarios

Where can you get replacement rear screens for this

ociaravella - Contestar

Hi, how i reset firmware in this gopro? I have a problem with a bucle starting and it dont turn on, always restarting.

ISU AREY - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 12

Ultimos 7 días: 53

Ultimos 30 días: 221

Todo El Tiempo: 19,205