Saltar al contenido principal

GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement

Qué necesitas

  1. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement, Casing: paso 1, imagen 1 de 1
    • Power off your GoPro before beginning disassembly.

    • Unclip the black latch to the camera case and open the case.

  2. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement: paso 2, imagen 1 de 1
    • Gently pry the back open by inserting a metal spudger between the case and back panel.

  3. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement: paso 3, imagen 1 de 1
    • Disconnect the battery from the motherboard by unplugging the red, white, and black wires from the white adapter.

  4. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement: paso 4, imagen 1 de 1
    • Disconnect the ribbon cable from the lens by lifting the black latch and gently pulling the ribbon cable from the socket.

  5. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement: paso 5, imagen 1 de 1
    • Use a Phillips screwdriver (PH000) to remove the four screws around the white plastic piece.

    • Make sure to keep track of these screws as they are very small.

  6. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement: paso 6, imagen 1 de 1
    • Carefully remove the motherboard and white plastic piece from the case.

  7. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement, Micro USB/MicroSD Card Daughter Board: paso 7, imagen 1 de 2 GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement, Micro USB/MicroSD Card Daughter Board: paso 7, imagen 2 de 2
    • Remove the larger ribbon cable from the daughter board by lifting the black latch and pulling the ribbon cable gently from the socket.

    • Disconnect the smaller ribbon cable leading from the white plastic piece by simply pulling it from the socket.

  8. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement: paso 8, imagen 1 de 1
    • Remove the two screws located on each side of the board with a Phillips screwdriver.

    • The screws go through an L metal bracket that will come off with the screws.

  9. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement: paso 9, imagen 1 de 1
    • Separate the daughter board from the white plastic piece.

Conclusión

To reassemble your device, follow these instructions in reverse order.

5 personas más completaron esta guía.

River Drake

Miembro Desde 04/02/15

1,023 Reputación

5 Guías creadas

Equipo

Cal Poly, Team 12-2, Lancaster Spring 2015 Miembro de Cal Poly, Team 12-2, Lancaster Spring 2015

CPSU-LANCASTER-S15S12G2

4 Miembros

18 Guías creadas

4 comentarios

Wo kann ich ein daughterboard kaufen habt ihr da was für mich?

Lukas Blohm - Contestar

bravo! è scritto molto bene ed è stato utile. ma dove trovo il ricambio? non ci riesco!!!

michele - Contestar

Terrific guide. Does anyone know where to buy the “daughter board”?

fedebossert - Contestar

ide. Does anyone know where to buy the “daughter board”?

fedebossert - 05/27/20

<a href="https://www.w3schools.com/">Visit W3Schools.com!</a>

pavan kalyan - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 7

Ultimos 30 días: 17

Todo El Tiempo: 4,754