Repara tus cosas Comunidad Tienda

GoPro Hero 3 Silver Image Sensor Replacement

Qué necesitas

  1. GoPro Hero 3 Silver Image Sensor Replacement, Battery: paso 1, imagen 1 de 2 GoPro Hero 3 Silver Image Sensor Replacement, Battery: paso 1, imagen 2 de 2

    • Pull back on the tab on the back of GoPro to open the battery cover.

    Editar

  2. GoPro Hero 3 Silver Image Sensor Replacement: paso 2, imagen 1 de 1

    • Pull the battery out using the tab.

    Editar

  3. GoPro Hero 3 Silver Image Sensor Replacement, Image Sensor: paso 3, imagen 1 de 2 GoPro Hero 3 Silver Image Sensor Replacement, Image Sensor: paso 3, imagen 2 de 2

    • Use the plastic opening tool to remove the faceplate.

    • There is some adhesive and clips so be careful and the faceplate should pop right off.

    Editar

  5. GoPro Hero 3 Silver Image Sensor Replacement: paso 4, imagen 1 de 2 GoPro Hero 3 Silver Image Sensor Replacement: paso 4, imagen 2 de 2

    • Now that the faceplate is off, it is time to remove the 4 screws on each corner.

    • Use the T4 tool bit from the iFixit toolkit in order to remove the 4 screws on each corner.

    Editar

  6. GoPro Hero 3 Silver Image Sensor Replacement: paso 5, imagen 1 de 2 GoPro Hero 3 Silver Image Sensor Replacement: paso 5, imagen 2 de 2

    • Note: Make sure you remove the door cover of the USB, mini HDMI, and SD port before. Separating the motherboard will be easier.

    • Using the plastic opening tool, slowly pry open the motherboard assembly.

    Editar

  7. GoPro Hero 3 Silver Image Sensor Replacement: paso 6, imagen 1 de 2 GoPro Hero 3 Silver Image Sensor Replacement: paso 6, imagen 2 de 2

    • Use the spudger to gently pry off the connector of the housing to the motherboard.

    • You should now have the motherboard assembly and the housing separated.

    Editar

  8. GoPro Hero 3 Silver Image Sensor Replacement: paso 7, imagen 1 de 2 GoPro Hero 3 Silver Image Sensor Replacement: paso 7, imagen 2 de 2

    • Use the spudger to remove the heat shield tape and detach the image sensor from the motherboard.

    • Using the T4 Torx toolbit, remove the 4 screws that connect the sensor to the lens.

    Editar

  9. GoPro Hero 3 Silver Image Sensor Replacement: paso 8, imagen 1 de 2 GoPro Hero 3 Silver Image Sensor Replacement: paso 8, imagen 2 de 2

    • Remove the silver connector of the image sensor from the motherboard using the spudger to pry it off.

    • You should now be able to remove the image sensor by simply pulling it.

    Editar

    Where i can buy the image sensor, and for how much

    Yudha prabowo - Contestar

Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Autor

con 4 otros colaboradores

Jose Villa

Miembro Desde 04/01/15

297 Reputación

1 Guía escrita

Insignias: 10

+ 7 más insignias

Equipo

Cal Poly, Team 24-7, Lancaster Spring 2015 Miembro de Cal Poly, Team 24-7, Lancaster Spring 2015

CPSU-LANCASTER-S15S24G7

3 Miembros

21 Guías creadas

2 comentarios

After the sensor has been replaced, does the camera need any catibration?

enrilazaro - Contestar

Your pictures are really dark.

Nick Ruiz - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 2

Ultimos 30 días: 5

Todo El Tiempo: 1,853