Saltar al contenido principal

Gateway SA1 Screen Replacement

Qué necesitas

  1. Gateway SA1 Screen Replacement, Battery: paso 1, imagen 1 de 1
    • Move the latch to the right of the battery to unlock.

  2. Gateway SA1 Screen Replacement: paso 2, imagen 1 de 1
    • Slide the latch on the left directly below the battery to unlock and pull out the battery as shown.

    • The latch must be held in position to remove the battery.

  3. Gateway SA1 Screen Replacement, Screen: paso 3, imagen 1 de 2 Gateway SA1 Screen Replacement, Screen: paso 3, imagen 2 de 2
    • Remove the hinge covers by lifting each with the sharp point of the spudger.

    • Notice that the middle cover has a different shape and is more difficult to remove.

  4. Gateway SA1 Screen Replacement: paso 4, imagen 1 de 2 Gateway SA1 Screen Replacement: paso 4, imagen 2 de 2
    • Remove the six screw covers on the front bezel with the sharp point of the spudger.

    • The bottom two are more difficult to remove.

  5. Gateway SA1 Screen Replacement: paso 5, imagen 1 de 1
    • Remove the six 5.9 mm Philips screws securing the screen bezel.

  6. Gateway SA1 Screen Replacement: paso 6, imagen 1 de 3 Gateway SA1 Screen Replacement: paso 6, imagen 2 de 3 Gateway SA1 Screen Replacement: paso 6, imagen 3 de 3
    • Remove the front bezel by prying it off with the wedged end of the spudger.

    • Verify that your spudger does not touch the LCD.

    • The screen inverter is now exposed below the LCD.

  7. Gateway SA1 Screen Replacement: paso 7, imagen 1 de 1
    • Remove the single 3.8mm Phillips screw mounting the screen inverter to the computer.

  8. Gateway SA1 Screen Replacement: paso 8, imagen 1 de 2 Gateway SA1 Screen Replacement: paso 8, imagen 2 de 2
    • Use your finger, or the spudger, to pry the inverter board out.

    • This exposes the wires behind it.

  9. Gateway SA1 Screen Replacement: paso 9, imagen 1 de 1
    • Unplug the LCD back light cables from the right side of the screen inverter.

  10. Gateway SA1 Screen Replacement: paso 10, imagen 1 de 2 Gateway SA1 Screen Replacement: paso 10, imagen 2 de 2
    • Remove the six screws that mount the screen to the hinge mounts.

    • Two 2.5 mm Phillips screws.

    • Four 3.8 mm Phillips screws.

  11. Gateway SA1 Screen Replacement: paso 11, imagen 1 de 1
    • Unplug the cable from the webcam board.

    • Be gentle, do not use excessive force or you may break the connection.

  12. Gateway SA1 Screen Replacement: paso 12, imagen 1 de 1
    • Separate the screen from the display cover.

    • Do not touch the back of the screen.

  13. Gateway SA1 Screen Replacement: paso 13, imagen 1 de 2 Gateway SA1 Screen Replacement: paso 13, imagen 2 de 2
    • Remove the three tape strips that hold down the cables.

    • Be careful not to tear any of the tape. The piece holding down the webcam wires is especially delicate.

  14. Gateway SA1 Screen Replacement: paso 14, imagen 1 de 2 Gateway SA1 Screen Replacement: paso 14, imagen 2 de 2
    • Unplug the display data cable from the screen connector.

    • This connection is very fragile; do not use excessive force.

    • The screen should now be free from all wire connections.

  15. Gateway SA1 Screen Replacement: paso 15, imagen 1 de 1
    • Remove the four 2.8 mm Phillips screws that secure the screen to the mounting bracket using a screwdriver.

    • There will be two screws on either side of the mounting bracket.

  16. Gateway SA1 Screen Replacement: paso 16, imagen 1 de 1
    • You can now remove and replace the screen.

Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Diego Carteno

Miembro Desde 04/15/10

258 Reputación

7 Guías creadas

Equipo

Cal Poly, Team 24-20, Regan Spring 2010 Miembro de Cal Poly, Team 24-20, Regan Spring 2010

CPSU-REGAN-S10S24G20

4 Miembros

14 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 18

Todo El Tiempo: 18,897