Introducción

This guide involves further disassembly of the clock radio and will require using several different tools and techniques, including using a soldering iron. If you need help on how to use a soldering iron, consult this iFixit guide: Cómo soldar y desoldar conexiones

  1. Find the battery compartment on the bottom of the clock radio. Using your thumb, push the compartment cover latch toward the battery. With the latch pushed in, pull the compartment cover upward to remove it..
    • Find the battery compartment on the bottom of the clock radio.

    • Using your thumb, push the compartment cover latch toward the battery.

    • With the latch pushed in, pull the compartment cover upward to remove it..

  2. Lift the battery from the compartment. Pull the battery up and gently disconnect it from the battery connector.
    • Lift the battery from the compartment.

    • Pull the battery up and gently disconnect it from the battery connector.

  3. Using a Phillips #00 Screwdriver, unscrew the six 12mm screws from around the bottom of the clock radio. Using a Phillips #00 Screwdriver, unscrew the six 12mm screws from around the bottom of the clock radio.
    • Using a Phillips #00 Screwdriver, unscrew the six 12mm screws from around the bottom of the clock radio.

  4. Gently pull the liquid crystal display (LCD) cover off.
    • Gently pull the liquid crystal display (LCD) cover off.

  5. ¡Envío gratuito para todos los pedidos de más de USD100.00 o que contengan un Pro Tech Toolkit!

    Visita Nuestra Tienda
  6. Lift the top off. Two gray, plastic internal pieces will fall out when you do this; set them aside. Lift the top off. Two gray, plastic internal pieces will fall out when you do this; set them aside.
    • Lift the top off. Two gray, plastic internal pieces will fall out when you do this; set them aside.

  7. Using the wire cutters, carefully cut the plastic wire tie. Using the wire cutters, carefully cut the plastic wire tie.
    • Using the wire cutters, carefully cut the plastic wire tie.

  8. Grip the speaker.
    • Grip the speaker.

    • Lift the speaker from the holder.

  9. Locate the two 6mm screws on the PCB. Using a Phillips #0 Screwdriver, unscrew the two 6 mm screws from the PCB.
    • Locate the two 6mm screws on the PCB.

    • Using a Phillips #0 Screwdriver, unscrew the two 6 mm screws from the PCB.

  10. Raise the PCB to expose the AM-FM switch dial screw. Using a Phillip's #01 Screwdriver, unscrew the one 3mm screw from the middle of the AM-FM switch dial.
    • Raise the PCB to expose the AM-FM switch dial screw.

    • Using a Phillip's #01 Screwdriver, unscrew the one 3mm screw from the middle of the AM-FM switch dial.

  11. Locate the AM-FM pins on the PCB. Carefully apply the hot soldering iron to the solder on top of the AM-FM pins. Gently and firmly push on the pins with the Spudger to remove the switch from the underside of the PCB.
    • Locate the AM-FM pins on the PCB.

    • Carefully apply the hot soldering iron to the solder on top of the AM-FM pins.

    • Gently and firmly push on the pins with the Spudger to remove the switch from the underside of the PCB.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Dominick Giguere

Miembro Desde 28/10/14

818 Reputación

6 Guías creadas

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 4

Todo El Tiempo: 484