Saltar al contenido principal

Introducción

Although a cracked screen would be hard to manage with this device, replacing the LCD screen is relatively easy.

  1. Using a 1.5mm Hex Screwdriver, remove the two 3.0 mm hex screws on the front of the camera. Using a Phillips #00 screwdriver, remove two 3.0 mm screws on the bottom of the front face. Using a Phillips #00 screwdriver, remove two 3.0 mm screws on the bottom of the front face.
    • Using a 1.5mm Hex Screwdriver, remove the two 3.0 mm hex screws on the front of the camera.

    • Using a Phillips #00 screwdriver, remove two 3.0 mm screws on the bottom of the front face.

  2. Using a Phillips #00 screwdriver, remove 3.0 mm screws on the bottom of the camera closer to the back. Using Phillips #00 screwdriver remove two 3.0 mm screws on the back of the camera. This will remove the eyelet for the camera strap and the rear cover. Using Phillips #00 screwdriver remove two 3.0 mm screws on the back of the camera. This will remove the eyelet for the camera strap and the rear cover.
    • Using a Phillips #00 screwdriver, remove 3.0 mm screws on the bottom of the camera closer to the back.

    • Using Phillips #00 screwdriver remove two 3.0 mm screws on the back of the camera. This will remove the eyelet for the camera strap and the rear cover.

  3. Using a Phillips #00 screwdriver, remove the two 3.0 mm screws.
    • Using a Phillips #00 screwdriver, remove the two 3.0 mm screws.

  4. Using a 1.5mm Hex screwdriver, remove 3.0 mm hex screw on top edge of silver panel. Using a Phillips #00 screwdriver, remove the 3.0 mm screw on bottom edge. Once both screws are removed the silver side casing will slide off.
    • Using a 1.5mm Hex screwdriver, remove 3.0 mm hex screw on top edge of silver panel.

    • Using a Phillips #00 screwdriver, remove the 3.0 mm screw on bottom edge.

    • Once both screws are removed the silver side casing will slide off.

  5. Kits de Reparación de Android

    Estás a un kit de tu nueva pantalla o batería.

    Comprar Ahora

    Kits de Reparación de Android

    Estás a un kit de tu nueva pantalla o batería.

    Comprar Ahora
  6. Unlatch the four clasps located on each side of the camera by hand. The fourth clasp is concealed by the battery door. To reach the clasp see Fujifilm XP20 Battery Replacement for instructions. The fourth clasp is concealed by the battery door. To reach the clasp see Fujifilm XP20 Battery Replacement for instructions.
    • Unlatch the four clasps located on each side of the camera by hand.

    • The fourth clasp is concealed by the battery door. To reach the clasp see Fujifilm XP20 Battery Replacement for instructions.

  7. Using a Phillips #00 screwdriver, remove the seven 3.0 mm screws. Remove the remaining five 3.0 mm screws which hold the rear case and the control panel together. The rear panel is now free from the camera.
    • Using a Phillips #00 screwdriver, remove the seven 3.0 mm screws.

    • Remove the remaining five 3.0 mm screws which hold the rear case and the control panel together.

    • The rear panel is now free from the camera.

  8. Take the spudger and wedge it in between the screen and the frame. Slowly make your way around the screen with the spudger just enough to separate the screen from the frame. Slowly make your way around the screen with the spudger just enough to separate the screen from the frame.
    • Take the spudger and wedge it in between the screen and the frame.

    • Slowly make your way around the screen with the spudger just enough to separate the screen from the frame.

  9. Take the spudger again and wedge it in the thinner frame to pry the LCD screen from the frame. Make your way around with the spudger just enough to separate the screen and frame once again.
    • Take the spudger again and wedge it in the thinner frame to pry the LCD screen from the frame.

    • Make your way around with the spudger just enough to separate the screen and frame once again.

  10. Take the spudger and wedge it very carefully between the LCD screen and the very thin and fragile frame. Very carefully make your way around the frame with the spudger, while making sure not to use too much force. Otherwise the screen will be damaged.
    • Take the spudger and wedge it very carefully between the LCD screen and the very thin and fragile frame.

    • Very carefully make your way around the frame with the spudger, while making sure not to use too much force. Otherwise the screen will be damaged.

  11. Detach the LCD screen from the motherboard by detaching the orange ribbon.
    • Detach the LCD screen from the motherboard by detaching the orange ribbon.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Stephen Harden

Miembro Desde 08/10/16

243 Reputación

2 Guías creadas

Equipo

IUPUI, Team 1-1, Wilson Fall 2016 Miembro de IUPUI, Team 1-1, Wilson Fall 2016

IUPUI-WILSON-F16S1G1

3 Miembros

3 Guías creadas

Añadir comentario

Ver Estadísticas:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 6

Global: 451