Repara tus cosas Comunidad Tienda

Flip Video Ultra Power button Replacement

Introducción

This guide will walk you through on how to remove the power button and replace it. You will need the iFixit Opening Tool and the Phillips #1 Screwdriver. It should take no more than 15 minutes, if it takes more than that then you may have done something wrong.

Qué necesitas

  1. Flip Video Ultra Power button Replacement, Power button: paso 1, imagen 1 de 1

    • Unlock the battery cover by sliding the switch to the unlock position.

    Editar

  2. Flip Video Ultra Power button Replacement: paso 2, imagen 1 de 1

    • Remove the battery cover by sliding it down the camera.

    Editar

  3. Flip Video Ultra Power button Replacement: paso 3, imagen 1 de 1

    • Remove the batteries

    Editar

  4. Flip Video Ultra Power button Replacement: paso 4, imagen 1 de 1

    • Slide the black upper casing off from the device.

    Editar

  5. Flip Video Ultra Power button Replacement: paso 5, imagen 1 de 2 Flip Video Ultra Power button Replacement: paso 5, imagen 2 de 2

    • Remove the six 1mm screws from the back and upper casing with the Phillips Head screwdriver.

    Editar

  7. Flip Video Ultra Power button Replacement: paso 6, imagen 1 de 1

    • Remove the top casing from the bottom to reveal the inner circuit board.

    Editar

  8. Flip Video Ultra Power button Replacement: paso 7, imagen 1 de 2 Flip Video Ultra Power button Replacement: paso 7, imagen 2 de 2

    • When removing the back panel, the rubber buttons will become loose and likely fall off the board. This is normal and can easily placed back on the board once finished.

    • Remove the six 1mm screws with the 1 Phillips head screwdriver.

    Editar

  9. Flip Video Ultra Power button Replacement: paso 8, imagen 1 de 1

    • Gently separate the circuit board from the casing.

    Editar

  10. Flip Video Ultra Power button Replacement: paso 9, imagen 1 de 2 Flip Video Ultra Power button Replacement: paso 9, imagen 2 de 2

    • Unscrew the single 1mm screw from USB housing unit.

    Editar

  11. Flip Video Ultra Power button Replacement: paso 10, imagen 1 de 2 Flip Video Ultra Power button Replacement: paso 10, imagen 2 de 2

    • Unscrew the 2 1mm screws and gently separate camera wires from plastic casing.

    Editar

  12. Flip Video Ultra Power button Replacement: paso 11, imagen 1 de 1

    • Gently pry out the USB housing unit with the Ifxit Opening Tool.

    Editar

  13. Flip Video Ultra Power button Replacement: paso 12, imagen 1 de 3 Flip Video Ultra Power button Replacement: paso 12, imagen 2 de 3 Flip Video Ultra Power button Replacement: paso 12, imagen 3 de 3

    • Remove the two 1mm screws and separate the circuit board and camera from the plastic casing.

    Editar

  14. Flip Video Ultra Power button Replacement: paso 13, imagen 1 de 1

    • Unscrew the camera housing unit from the plastic case.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 2 otros colaboradores

Nathaniel Ruf

Miembro Desde 10/18/16

514 Reputación

5 Guías creadas

Insignias: 5

+ 2 más insignias

Equipo

UMass Dartmouth, Team 5-7, Martin Fall 2016 Miembro de UMass Dartmouth, Team 5-7, Martin Fall 2016

UMASSD-MARTIN-F16S5G7

3 Miembros

10 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 3

Ultimos 30 días: 7

Todo El Tiempo: 447